background image

2  /  THE BASICS

8 /  552

0 RETICLE
The 68 MOA ring with 1 MOA dot is ideal for fast target 

acquisition  It provides three usable aiming points  The 

aiming points above were based on the following load: 

 223 Cal  62 Gr  2,900 Vel  Other loads and calibers can 

also be used, but the operator will have to establish the 

ranges associated with the aiming points  When using a 

shotgun, the 68 MOA ring can be used to represent shot 

patterns, but will vary based on choke and shell selection 

XR308 RETICLE
The XR308 reticle was designed specifically for the 

military M240 machine gun  It was calculated with a  

 308 Cal  with 150 Gr  M59 FMJ at roughly 2,800 fps  

with a 24 8” barrel 

Reticles

HWS RETICLE ADVANTAGE
EOTECH’s Holographic technology provides a distinct advantage over typical red 

dots  EOTECH can offer any type of reticle pattern, as opposed to being limited to 

a single dot  EOTECH reticle designs are fabricated so that they can incorporate 

multiple trajectory points of aim, range assist features, and anti-torque or cant  

visual indicators 

HWS RETICLE PATTERNS
EOTECH’s reticle patterns greatly impact accuracy and fast target acquisition  

EOTECH’s reticle patterns feature a 68 MOA ring surrounding a 1 MOA center dot, 

allowing the shooter to quickly pick up a target; HWS allows for more complex 

reticle designs with minimal parallax error 

50 yds  

and 

200 yds 

7 yds 

.9

.6

.12

Summary of Contents for 552



























Reviews: