EOS ECON D3 Installation And Operating Instruction Download Page 6

General safety precautions

• 

This device can be used by children aged 
8 upwards and by persons with physical, 
sensory,  or  mental  disabilities,  or  who 
have  inadequate  experience  and  knowl-
edge if they are supervised or if they have 
received  adequate  instruction  in  how  to 
use the device safely and understand the 
associated  risks.  Children  may  not  play 
with  this  device.  Children  may  not  clean 
or carry out any user maintenance if un-
supervised. 

• 

Children  are  to  be  supervised  in  order  to 
make sure that they do not play with this 
device.

• 

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

Attention

:  It  is  forbidden  to  install 

the control box in a closed switch cabinet 
or behind a wooden panelling!

• 

The  electrical  installation  may  be  done 
only by a qualifi ed electrical technician.

• 

You must comply with the regulations of 
your power supply company and applica-
ble VDE regulations (DIN VDE 0100).

• 

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

 

WARNING

: Never attempt repairs or 

installations  yourself,  as  this  could  result 
in serious injury or death. Only a qualifi ed 
technician may remove the housing cover.

• 

Please note the dimensions in the assem-
bly instructions, especially when installing 
the temperature sensor. The temperature 
above the oven is critical for the temper-

ature  setting.  The  temperature  can  be 
held  within  operating  parameters  and 
a  minimal  temperature  gradient  inside 
the bench area of the sauna cabin can be 
achieved only if unit is assembled correct-
ly.

• 

The device may only be used as intended 
as a control unit for sauna ovens up to 9 
kW (up to 36 kW when combined with a 
contactor box).

• 

Completely  disconnect  the  control  unit 
from the electrical circuit, i.e. fl ip all circuit 
breakers or the main circuit breaker during 
each installation or repair. 

• 

Please  note  the  safety  and  installation 
information  from  the  sauna  oven  manu-
facturer.

• 

Always  heed  the  specifi cations  and  in-
structions of the cabin manufacturer, too.

• 

  If  control  units  with  remote  con-

trol  options*  are  used,  protection 
against  activation  when  the  heater  is 
covered is required. (e.g. cover protec-
tion Type 1-5 or S-Guard).

*Telecontrol = setting up, controlling or adjusting a 
unit by a command that can be given out of view 
of the unit by means of transfer media such as tele-
communication, audio technology or bus systems. 
(this also includes weekly timers)

6

GB

Summary of Contents for ECON D3


































Reviews: