background image

8

Guarantee

The guarantee is taken over according to the
legal regulations at present.

Manufacturer’s warrenty

-

The period of warrenty starts from the date
of purchase and lasts up to 2years for
commercial use and 3 years for private use.

-

Always include the completed warrenty
certificate when returning equipment.

-

The warrenty expires for appliances which
have been modified without manufacturer’s
explicit agreement.

-

Damages caused by incorrect operation or
handling through non-authorized persons are
not covered under the terms of warranty.

-

In the event of a claim, please indicate the
serial number as well as the article code
number and type name with expressive
description of the fault.

-

This warrenty covers damaged parts but no
defects due to wear and tear.

In case of complaint please return the equipment
in its original packaging or other suitable
packaging (caution: danger of transport damage)
to our service department.
Always include the completed warrenty
certificate when returning equipment.
Possible shipping costs arising from the transport
to and from point of repair cannot be borne by
us.
Outside of Germany please contact your
specialist dealer in case of warranty claims.
Direct warranty processing with our service
department is in this case not possible.

Equipment start-up date:

Stamp and signature of the authorized
electrician:

Service address:
EOS-Werke Günther GmbH
Adolf-Weiß-Str. 43
35759 Driedorf-Germany
tel  +49 (0)2775 82 240
fax +49 (0)2775 82 455
[email protected]
www.eos-werke.de

english

Attention!

Dear customer,
according to the valid regulations, the
electrical connection of the sauna heater
and the control box has to be carried out
through the specialist of an authorized
electric shop.
We would like to mention to the fact that
in case of a warrenty claim, you are kindly
requested to present a copy of the invoice
of the executive electric shop.

Summary of Contents for ECON 09









Reviews: