enware Wellbeing Livia LIV80WSET Installation And Maintenance Instructions Manual Download Page 3

www.enware.com.au 

Call 1300 369 27   

 3  

•  All supply lines must be flushed thoroughly to remove debris 

prior to the installation of this product, as per AS/NZS 
3500.1. Strainers (40 mesh) are recommended if debris is 
an ongoing problem.

•  A pressure reduction valve may be required to comply 

with the recommended maximum supply pressure and/or 
balanced pressure requirements.

INSTALLATION

1.  Prepare shower breech in wall, taking into account the 

wall depth required for the tap.  
Minimum 6mm, maximum 15mm from finished wall to the 
face of tap body. SEE IMAGE 01

2.  After the wall is finished, screw SBA spindle into tap body 

in wall. Use the hex provided on the SBA to tighten with a 
spanner. Do not over-tighten.  
(Max. torque 18Nm)  SEE IMAGE 02 
 
Take note of the way the handles turn.  
LTC (Anti-clockwise to close) is marked with blue. 
RTC (Clockwise to close) is marked with red on the 
spindle. SEE IMAGE 06

3.  Fit fibre washer [9] onto spindle and screw locknut [8] 

onto SBA spindle [10, 11]. Tighten locknut with a spanner. 
(Max. torque 30Nm)  SEE IMAGE 03

4.  Fit flange dome [6] onto spindle. Ensure the O-ring [7] is in 

place. SEE IMAGE 04

OPE
N

CLOSED

 80 

 67 

 15 MAX. 

 6 MIN. 

 

61 

G5/8" (BSP

)

IMAGE 01

MAX 18Nm

IMAGE 02

installation

IMAGE 04

MAX 30Nm

IMAGE 03

Summary of Contents for Wellbeing Livia LIV80WSET









Reviews: