Envision Xenics Gobi-384-25mm User Manual Download Page 26

Page: 26 / 28

User Manual

Gobi-640-17µm and Gobi-384-25µm-GigE, CL, CXP Camera

6. Getting Started

6.1. Install the Software

First perform the Xeneth installation and when necessary the SDK installation as well (see
chap.

5 Software Installation

6.2. Connect the Cables

The cable information and interfaces is described in chap.

Electrical Interface

6.3. Connect the Camera via Xeneth

When connecting the GigE interface: see

(Ref. 6)

otherwise do the following:

Click the Xeneth shortcut on the desktop to start up Xeneth (see

Figure 6-1

). The

connection dialog will become visible (see

Figure 6-2

). When the camera is not shown,

click the refresh button on the dialog. Select the camera, together with the calibration data
suited for it. For more details, consult the Xeneth User Manual, section Connection setup -
Settings.

Figure 6-1 Xeneth shortcut

Figure 6-2 Connection dialog - settings

www.envision.co.kr

•Supporting your Vision

(주)앤비젼

서울시 금천구 가산동 550-1 IT캐슬 1동 603호 (153-768)

Tel.

02. 2624. 5503

Fax.

02. 2082. 6427

e-mail.

[email protected]

Summary of Contents for Xenics Gobi-384-25mm





























Search results

Summary of Contents for Xenics Gobi-384-25mm

Reviews:

Related manuals for Xenics Gobi-384-25mm

Brands by name

Popular brands

Envision Xenics Gobi-384-25mm, User Manual

Search results

Summary of Contents for Xenics Gobi-384-25mm

Reviews:

Related manuals for Xenics Gobi-384-25mm

Brands by name

Popular brands