background image

 User Manual 

Gobi-640-17µm and Gobi-384-25µm-GigE, CL, CXP Camera  

 

2. Mechanical & Electrical Specifications 

The mechanical drawings of Gobi-640/Gobi-384-GigE and CL can be found i

Appendix B

. 

2.1.  Gobi-640-17µm Detector Specifications 

The detector specifications are summarized i

Table 2-1

. 

 

 

 

 

 

 

 

Table 2-1 Gobi-640-17µm detector specifications 

 

2.2.  Gobi-640-17µm GigE, CL & CXP Camera 

Specifications 

The camera specifications are listed i

Table 2-2

. 

Feature 

GigE 

CL 

CXP 

Frame rate (full 
frame) 

50 Hz 

Shutter  

Yes 

Cooling 

No 

A/D conversion 
resolution 

16 bit 

Input Voltage 

12V±10% 

Power over CoaXPress 

(PoCXP) 

Ambient operating 
temperature 

-40 to 60°C 

Storage Temperature 

-45 to 85°C 

Vibration 

5g (20 to 2000 Hz), according to MIL-STD883J 

Shock 

40g, 11ms, according to MIL-STD810G 

Electrical interface 

GigE  Vision (image 
acquisition and camera 
control) 

Camera Link (image 
acquisition and camera 
control) 

CoaXPress (image 
acquisition and camera 
control) 

Trigger 

In or out via SMA 

In or out via SMA or CL-
CC1 

In or out via SMA 

Parameter 

Specification 

Array Type 

a-Si micro-bolometer 

# pixels 

640 (W) x 480 (H)  

Pixel pitch 

17 µm 

Spectral Band 

8-14 µm 

NETD 

(1)  50 mK @ 30°C with F/1 lens (typical value) 
(2)  <75 mK @ 30°C with F/1 lens 

Detector Operating Mode 

Rolling Shutter Mode 

Window of interest 

Yes  

Exposure time range 

1 – 80 µs

 

Pixel Operability 

>99% 

www.envision.co.kr

  

•Supporting your Vision

(주)앤비젼

 서울시 금천구 가산동 550-1 IT캐슬 1동 603호 (153-768)

Tel.

 

02. 2624. 5503 

  Fax.

 

02. 2082. 6427

   

e-mail.

 

[email protected] 

Summary of Contents for Xenics Gobi-384-25mm





























Reviews: