background image

3/11

ENVIRONMENTAL SENSOR TECHNOLOGY CO. INC.

III.

III.

III.

III. Performance

Performance

Performance

Performance Parameters

Parameters

Parameters

Parameters

Product name

Gas detection alarm

Sensor name

Optional (electrochemical

sensor)

Type of product

EST-2000

Type of sensor

Optional

External power

supply

5VDC/500mA

Detecting target

Toxic gas (optional)

Type of battery

Lithium ion battery

Detection principle

Electrochemical

Battery voltage

3.7V (charge limitation 4.2V)

Detection method

Diffusion

Battery capacity

800mAh

Detection range

Optional

Shutdown current

< 0.1mA

Accuracy

±5%FS

Startup current

< 10mA

Resolution

Optional

Alarm current

< 50mA

Operating

temperature

-10

-40

Protection class

IP65 dustproof and waterproof

Humidity

0-95%RH

Way of display

LCD liquid crystal display

Pressure range

860-1060hpa

Way of alarm

Two levels of the sound and light alarm

Preheat time

60 seconds

Alarm error

≤±10% alarm set value

Response time

T90≤30S (most)

Data storage

N/A

Service life

2 years (in the air)

Signal output

N/A

Zero drift

≤±2%FS/6h

Dimensions of

appearance

120*60*35mm

Span drift

≤±5%FS/6h

Weight of

machine

≤ 250g (including batteries)

Repeatability

≤±2%FS

Note:

Note:

Note:

Note: Please

Please

Please

Please refer

refer

refer

refer to

to

to

to the

the

the

the corresponding

corresponding

corresponding

corresponding sensor

sensor

sensor

sensor technical

technical

technical

technical manual

manual

manual

manual for

for

for

for the

the

the

the sensor

sensor

sensor

sensor parameters.

parameters.

parameters.

parameters.

Summary of Contents for EST-1000














Reviews: