background image

Introduction

N

ote

 e

mplacemeNt

 

de

 

l

étiquette

:

L

a

 

pLaque

 

signaLétique

 

se

 

trouve

 

sur

 

Le

 

dos

 

de

 

La

 

couverture

 

du

 

cendrier

.

i

mportaNt

 

de

 

doNNées

 

de

 

sécurité

:

S’il vous plaît lire le manuel du propriétaire avant toute installation ou l’utilisation poêle aux granules. Le 

non respect de ces instructions peut entraîner des dommages matériels, des blessures ou même la mort. 

Contactez votre bâtiment local ou un incendie officielle pour obtenir un permis et toute information sur 

les restrictions d’installation et les exigences d’inspection dans votre localité.
Pour éviter la possibilité d’un incendie, veiller à ce que l’appareil est correctement installé en adhérant 

aux instructions d’installation. Un concessionnaire de ENVIRO sera heureux de vous aider à obtenir des 

informations au sujet de vos codes de construction locaux et des restrictions d’installation.
Assurez-vous de maintenir l’intégrité structurelle de la maison lors du passage d’un évent à travers les 

murs, plafonds ou toits.
Le système d’échappement du poêle fonctionne avec une pression de chambre de combustion et une 

pression négative de la cheminée légèrement positive. Il est très important de garantir que le système 

d’échappement et être scellé étanche à l’air. Le pan de cendres et la porte doivent être fermées pour un 

fonctionnement correct et sûr de la poêle à granulés.
Ne pas brûler avec de l’air de combustion insuffisant. Une vérification périodique est recommandé de 

veiller à l’air de combustion approprié est admis dans la chambre de combustion. Réglage de l’air de 

combustion approprié est réalisé en ajustant l’amortisseur à glissière, situé sur le côté gauche du poêle.
Lors de l’installation du poêle dans une maison mobile, il doit être mis à la terre au châssis de l’acier de 

la maison et boulonné au plancher. Assurez-vous que l’intégrité structurale de la maison est maintenue 

et toute construction répond aux codes de construction locaux.
Suie mineur ou de créosote peut s’accumuler lorsque le poêle fonctionne dans des conditions incorrectes, 

comme une combustion très riche (noir à pointe, flammes orange paresseuses).
Si vous avez des questions au sujet de votre poêle ou de l’information mentionnée ci-dessus, s’il vous 

plaît sentir libre de contacter votre revendeur local pour obtenir des précisions et de commentaires.

a

vertissemeNts

 

de

 

sécurité

 

et

 

recommaNdatioNs

:

Prudence: Ne pas se connecter à aucun conduit ou système de distribution d’air.

                Ne pas brûler de déchets ou de liquides inflammables comme de l’essence, du   

naphte ou de l’huile de moteur. NE PAS BRÛLER: bois traité, bois de l’eau salée, 

le charbon, le charbon de bois, les ordures, en plastique, des solvants ou des 

papiers colorés. Ces matériaux contiennent des chlorures qui va rapidement se 

corroder et Warp surfaces métalliques qui annule la garantie. Unité chaude lors 

de l’opération. Tenir les enfants, vêtements et meubles éloignés. Le contact peut 

provoquer des brûlures de la peau.

S’il vous plaît lire le manuel du propriétaire avant toute installation ou l’utilisation poêle aux granules. Le 

non respect de ces instructions peut entraîner des dommages matériels, des blessures ou même la mort. 

Toute modification non autorisée de l’appareil ou de l’utilisation de pièces de rechange non recommandés 

par le fabricant est interdite.

Avertissement

: Certaines pièces de l’appareil, en particulier les surfaces externes, seront chaudes au 

toucher lorsqu’il est en fonctionnement et en raison des soins devront être prises. Ne placez jamais du 

bois, du papier, des meubles, des rideaux ou d’autres matériaux combustibles dans les 80cm (31½ “) de 

l’avant de l’appareil, 20cm (7⅞”) de chaque côté, et de 10cm (4 “) à l’arrière de l’appareil. Ne laissez pas 

les enfants ou les animaux de le toucher quand il fait chaud.

3

Summary of Contents for Mini A







































Reviews: