background image

Pixel Octo User Manual 

For latest version visit: 

www.enttec.com 

10 December 2019 

M-files ID: 4836041 

Page|

Settings 

 

The Settings page allows a user to do the following:

 

 

Change a device name for identification

 

 

Enable/disable DHCP

 

 

Specify static network settings

 

 

Set the output LED Protocol

 

 

Set the number of mapped pixels

 

 

Configure how colours are mapped to pixels

 

 

Reset to factory defaults

 

 

Reboot device

 

Direct 

Direct  can  be  activated  by  clicking  on  the  Use 
Direct mode button in the Direct page as shown in 
the image below

 

 

When activated, the word Direct will be displayed 
next to the ENTTEC logo as shown in the image.

 

 

DMX Protocols 

KiNET

 

Supported commands: 

 

Discover device 

 

Discover ports on device 

 

Change device name 

 

Change device IP 

 

Portout commands 

 

DMX out commands 

 

KGet Command 

o

 

KGet Subnet Mask 

o

 

KGet Gateway 

o

 

KGet port universe (port 1 and 2) 

 

KSet commands 

o

 

KSet Subnet Mask 

o

 

KSet Gateway 

o

 

KSet port universe (port 1 and 2) 

o

 

KSet device to boot 

Art-NET

 

Supports  Art-NET  1/2/3.  Each  output  can  be 
assigned a  start universe  in  the  range  0  to  32764 
(when universe/output = 4).

 

sACN

 

Outputs  can  be  assigned  a  start  universe  in  the 
range  1-63996  (when  universe/output  =  4).  1 
multicast universe is supported for sACN sync.

 

ESP

 

Outputs  can  be  assigned  a  start  universe  in  the 
range  0-252  (when  universe/output  =  4).  More 
details  of  the  ESP  protocol  can  be  found  at 

www.enttec.com

Summary of Contents for 71520
















Reviews: