Entrotec PRO-DPC Installation And Setup Manual Download Page 13

Page: 13 / 28

Provision

Provisioning Systems with an Entrotec Connect Server

8.2.1

Configure SIP Server Settings

ii.

Navigate to

Network Settings

SIP Server

FIGURE 8-4

iii.

Uncheck

Enable

, this disables the internal device SIP Server which is on as default.

iv.

For

Sever Type

select

Express\DSS

Enter the Entrotec Connect Server

IP Address

Port

5080.

vi.

Optional - enter the

Domain VDP

SIP Server Username

and

SIP Server Password

vii.

Press

Save

NOTE

The device will reboot if the internal device SIP Server is enabled or disabled.

8.2.2

Configure the Alternate SIP Server

After applying the

SIP server

settings in Section 8.2.1, you can configure an alternate SIP Server.

The

Alternate SIP

server will take over from the original in case of any down time. The panel

configured to be the

Alternate SIP Server

is typically the main door panel in the system.

FIGURE 8-5

This can be configured following these steps:

Set the

Alternate IP Addr.

to the main door panel IP address.

ii.

Insert the login details for the main door panel in the

Alternate Username

and the

Alternate

Password

. These are the login details setup during initialisation (Section 6).

iii.

Check the

Alternate Server

to enable it.

iv.

Click

Save

to save the configuration.

Summary of Contents for PRO-DPC





























Search results

Summary of Contents for PRO-DPC

Reviews:

Related manuals for PRO-DPC

Brands by name

Popular brands

Entrotec PRO-DPC, Installation And Setup Manual

Search results

Summary of Contents for PRO-DPC

Reviews:

Related manuals for PRO-DPC

Brands by name

Popular brands