3
4
5
INSTALLING THE MODULE
Handling the Module
To prevent electrostatic damage, observe the following guidelines:
•
Do not remove the module from its packaging until you are ready to
install it.
•
Do not touch any of the module’s pins, connectors or components.
•
Hold the module only by its edges or front panel.
•
Wear an anti-static wristband connected to a suitable earth ground
whenever handling the module.
•
Store or transport this module only in appropriate anti-static packaging.
Equipment Checklist
After unpacking the SSR-ATM29-02, check the contents of the box to be sure
you received the following items:
•
One SSR-ATM29-02 module in static bag
•
One disposable anti-static wristband
Tools
This installation requires the following tools:
Preliminary Setup
Firmware Image Requirements
Version 3.0.0.0 or later.
CLI Setup
Enter the following commands at the CLI before implementing any
configurations.
1.
Enable —> Configuration —> <Enter>.
2.
Once you reach the configuration prompt, you can create the ATM
interface using CLI commands as described in the ATM section of the
X-Pedition CLI manual. Enter the ? character to view the options available
to you in configuration mode.
Connector Pin Assignments
The connector pins are assigned as follows:
Hotswap
You may install this module into a live system without powering off the device.
An active module can be removed from a live system only under the following
conditions:
•
Press the hotswap button. The green LED should turn off and the yellow
LED should turn on. When the yellow LED is on, you can safely hotswap
the module.
Instructions
1.
Remove the coverplate. If a coverplate is installed over the expansion slot,
remove the coverplate.
2.
Slide the SSR-ATM29-02 into the expansion slot. Slide the module all
the way into the slot, firmly but gently pressing to ensure that the pins on
the back of the module are completely seated in the backplane.
Figure 1
Insert card between card guides
3.
Tighten captive screws. Align the captive screws with the holes in the face
of the module and tighten the screws to secure the SSR-ATM29-02 to the
chassis.
TROUBLESHOOTING
Proper Boot sequence
•
The control module on the chassis should indicate that the board was
detected and is operating correctly.
Common Errors
•
Make sure the chassis is connected to a terminal through a console port.
ADDITIONAL INFORMATION
For additional information about installing this module or to learn more about
what capabilities are included in the firmware release you are using, visit the
Enterasys Networks web site.
Getting Help
For additional support related to the Common CLI syntax or this document,
contact Enterasys Networks using one of the following methods:
Before contacting Enterasys Networks for technical support, have
the following information ready:
•
Your Enterasys Networks service contract number
•
A description of the failure
•
A description of any action(s) taken to resolve the problem (e.g., changing
mode switches, rebooting the unit)
•
The serial and revision numbers of all involved Enterasys Networks
products in the network
•
A description of your network environment (layout, cable type, etc.)
•
Network load and frame size at the time of trouble (if known)
ELECTRICAL HAZARD: Only qualified personnel should perform
installation procedures.
CAUTION: The SSR-ATM29-02 module is easily damaged by
electrostatic discharge.
Anti-static wristband
Phillips screwdriver
Table 2
APHY-82 and APHY-92 Pin Assignments
Pin
Connection
1
Receive analog signal
2
Receive reference
3
Pin used for shield reference if you use a shielded cable
4
Transmit analog positive pulse
5
Transmit analog negative pulse
6
Pin used for shield reference if you use a shielded cable
CAUTION: Before performing any upgrade or installation, ensure
that you are properly “grounded” to avoid electrostatic discharge.
However, since you can hotswap the SSR-ATM29-02, the XP 8000/
8600 may continue running.
NOTE: Make sure the circuit card (and not the metal plate) is
between the card guides. Check both the upper and lower tracks.
Online
Offline
SSR-8
SSR-ATM29-02
ATM MODULE
Card Guides
Circuit Card
Metal Plate
Hot
Swap
P1
P2
World Wide Web
http://www.enterasys.com/
Phone
(603) 332-9400
Internet mail
FTP
Login
Password
ftp://ftp.enterasys.com
anonymous
your email address
To acquire the latest image
for this product and any
available release notes
http://www.enterasys.com/download
Additional documentation
http://www.enterasys.com/support/manuals
To send comments or suggestions concerning this document, contact the
Technical Writing Department via the following email address:
[email protected]
Please include the document Part Number in the email message.
SSR-ATM29-02
Quick Start
Web Site:
http://www.enterasys.com/
9033687-01
