Installing Optional Mini-GBICs
SecureStack C2 Installation Guide 3-3
Installing Optional Mini-GBICs
This
section
describes
how
to
install
Mini
‐
GBICs
in
any
of
the
SFP
port
slots
(45
through
48
of
C2G124
‐
48P,
or
49
through
52
of
C2H124
‐
48P.
It
is
recommended
that
the
options
be
installed
first
in
a
new
installation.
Preparing to Install a Mini-GBIC
Before
installing
the
Mini
‐
GBIC,
proceed
as
follows:
1.
Before
removing
the
Mini
‐
GBIC
from
the
antistatic
packaging,
it
is
recommended
that
you
use
an
antistatic
wrist
strap
(not
supplied)
to
prevent
damage
from
static
discharge.
To
use
the
wrist
strap,
refer
to
the
instructions
provided
with
your
antistatic
wrist
strap.
2.
Remove
the
Mini
‐
GBIC
from
its
packaging.
3.
If
there
is
a
protective
dust
cover
(see
5
in
Figure 3
‐
1
or
Figure 3
‐
2
)
in
the
Mini
‐
GBIC
connector,
do
not
remove
it
at
this
time.
Installing a Mini-GBIC
To
install
a
Mini
‐
GBIC
that
has
an
MT
‐
RJ
connector,
refer
to
Figure 3
‐
1
,
or
for
a
Mini
‐
GBIC
with
an
LC
connector,
refer
to
Figure 3
‐
2
,
and
proceed
as
follows:
1.
Hold
the
Mini
‐
GBIC
with
the
top
side
positioned
as
shown,
and
the
7
‐
pin
edge
connector
facing
the
port
slot.
Warning:
Do not use optical instruments to view laser output. The use of optical
instruments to view laser output increases eye hazard.
Advertencia:
No utilizar instrumentos opticos para ver el laser. El uso de instrumentos
opticos para ver el laser incrementa el riesgo de perdida de la vision.
Warnhinweis:
Benutzen sie keinesfalls optische Hilfmittel, um die Funktion des Lasers zu
überprüfen, es könnte ihr Augenlicht gefährden.
Caution:
Carefully follow the instructions in this manual to avoid damaging the Mini-GBIC
and switch.
The Mini-GBIC and switch are sensitive to static discharges. Use an antistatic wrist strap
and observe all static precautions during this procedure. Failure to do so could result in
damage to the Mini-GBIC and switch. Always leave the Mini-GBIC in the antistatic bag or
an equivalent antistatic container when not installed.
Precaución:
Siga las instrucciones del manual para no dañar el Mini-GBIC ni del aparato,
puesto que son muy sensible a las descargas de electricidad estática. Utilice la pulsera
antiestática y tome todas las precauciones necesarias durante este procedimiento. Si no
lo hace, podría dañar el Mini-GBIC o del aparato. Mientras no esté instalado, mantenga el
Mini-GBIC en su bolsa antiestática o en cualquier otro recipiente antiestático.
Note:
If the Mini-GBIC is one with an RJ45 connector (not shown), the installation
procedure is the same as described below. However, the Mini-GBIC has a wire handle to
release it.
Summary of Contents for SecureStack C2 C2G124-48P
