Frequency Table
No
Frequency
Beeps
1
446.00625 MHz
•
2
446.01875 MHz
• •
3
446.03125 MHz
• • •
4
446.04375 MHz
• • • •
5
446.05625 MHz
• • • • •
6
446.06875 MHz
• • • • • •
7
446.08125 MHz
• • • • • • •
8
446.09375 MHz
• • • • • • • •
CTCSS (PL) Tone Table
Ref
CTCSS
(Hz)
Beeps
▬
●
0
0
See p13 Check configuration
1
62.5
-
1
2
67
-
2
3
69.3
-
3
4
71.9
-
4
5
74.4
-
5
6
77
-
6
7
79.7
-
7
8
82.5
-
8
9
85.4
-
9
10
88.5
1
0
11
91.5
1
1
12
94.8
1
2
13
97.4
1
3
14
100
1
4
15
103.5
1
5
16
107.2
1
6
17
110.9
1
7
18
114.8
1
8
19
118.8
1
9
20
123
2
0
21
127.3
2
1
22
131.8
2
2
23
136.5
2
3
24
141.3
2
4
25
146.2
2
5
Ref
CTCSS
(Hz)
Beeps
▬
●
26
151.4
2
6
27
156.7
2
7
28
159.8
2
8
29
162.2
2
9
30
165.5
3
0
31
167.9
3
1
32
171.3
3
2
33
173.8
3
3
34
177.3
3
4
35
179.9
3
5
36
183.5
3
6
37
186.2
3
7
38
189.9
3
8
39
192.8
3
9
40
196.6
4
0
41
199.5
4
1
42
203.5
4
2
43
206.5
4
3
44
210.7
4
4
45
218.1
4
5
46
225.7
4
6
47
229.1
4
7
48
233.6
4
8
49
241.8
4
9
50
250.3
5
0
51
254.1
5
1
16
HT644E
15
Radio Cloning HT446E
Radio cloning allows you to copy the programmed channel and button setup information from a
‘master’ radio into other unprogrammed radios without the use of a PC. Cloning is performed by
connecting two radios together using a HTCL cloning lead.
How to clone a radio
Connect the HTCL lead to the accessory socket on both radios. Ensure the master radio is
powered up before the slave radio.
1.
Master Radio (sending radio)
Put the radio you will be using to programme other radios into ‘clone send’ mode by pressing the
PTT and bottom side function buttons at the same time and turn the power on. The radio will emit
a alert and the LED will alternately flash yellow / red.
2.
Slave Radio (receiving radio)
Put the radio you wish to programme into ‘clone receive’ mode by pressing the lower side function
button at the same time and turn the power on. The radio will emit a short “beep” and the LED will
alternately flash yellow / green.
Transferring data
Master radio
Press the PTT switch on the radio. A short beep will be emitted to
confirm the process has been initiated.
The radio’s LED will flash red whilst data transfer is in progress. Once all the
data has successfully transfered the LED will flash yellow/red.
Slave radio
The radio’s LED will flash green whilst data transfer is in progress.
Once all the data has successfully transferred the LED will flash yellow/green. To
return the radio to normal mode switch the radio off then on again.
The ‘master’ radio will automatically return to ‘clone send’ mode indicated by the LED alternately
flashing yellow / red. You may now either programme another radio or press the orange button to
return the ‘master’ radio to normal.
To return to clone send mode if an error occurs, press the orange button on top of the ‘master
radio’. A alert will be emitted and the radio’s LED alternately flash yellow / red).
