enphase IQ7-B1200-LN-I-INT01-RV0 Installation Manual Download Page 19 | Manualshive

Page: 19 / 24

enphase IQ7-B1200-LN-I-INT01-RV0 Installation Manual Download Page 19

© 2019 Enphase Energy Inc.

19

Battery LED is Solid Yellow

•

Check the temperature in the room and increase cooling and/or ventilation as required to meet

temperature requirements. The Battery requires an ambient temperature between -20° C and 45° C,

and where relative humidity is between 5 and 95 percent.

•

Check that the front, top, and sides of the AC Battery array have at least 300 mm of unobstructed

clearance.

NOTE

: If the AC Battery registers a high temperature event, it responds by reducing

operation to correct internal temperature.

System Alert: “AC Battery(ies) with Critical Temperature”

•

Check the temperature in the room and increase cooling and/or ventilation as required to meet

temperature requirements. The AC Battery requires an ambient temperature between -20° C and 45°

C, and where relative humidity is between 5 and 95 percent.

•

Check that the front, top, and sides of the AC Battery array have at least 300 mm of unobstructed

clearance.

NOTE

: If the AC Battery registers a high temperature event, it responds by reducing

operation to correct internal temperature.

«
...
17
18
19
20
21
...
»

Summary of Contents for IQ7-B1200-LN-I-INT01-RV0

























Reviews:

No comments