manualshive.com logo in svg

EnOcean STM110C, User Manual

Share
Download
EnOcean STM110C User Manual Download Page 21

USER MANUAL 

V0.904 

EnOcean GmbH 
Kolpingring 18a 
82041 Oberhaching 
Germany 

Phone +49.89.67 34 689-0 
Fax +49.89.67 

34 

689-50 

[email protected] 
www.enocean.com 

Subject to modifications 
STM110C User Manual V0.904 
February 18, 2008 2:00 PM 
Page 20/40 

 

STM110C 

 

 

In the figure left typical values are shown. In worst case the operating time in 
darkness may be 20% less! 

 

2.7  Radio Telegram of STM110C 

Frequency range and modulation scheme 
Because of the very low radiated field strength on average, products based on STM110C 
(315.0 MHz) can be approved in the USA and in Canada. The approval requirements can be 

found in chapter 4 of this paper. 
STM110C is based on ASK (amplitude shift keying) modulation with a bit rate of 125 kbit/s. 
 
Telegram content 
The payload of the telegram consists of: 

8 bit 

8 bit  8 bit  4 bit 

32 bit 

AD_2  AD_1 AD_0 DI_3..0  ID 

 

Transmission timing 
The transmission timing of the radio module STM110C has been developed to avoid possi-

ble collisions with data packages of other EnOcean transmitters as well as disturbances 
from the environment. 
With each transmission cycle, 3 identical subtelegrams are transmitted. The transmission of 
a subtelegram lasts approximately 1.2 ms. To optimize data security, each telegram is re-

peated twice within about 40 ms, whereas the delay between the three transmission bursts 
is effected at random. 
 
 

 

 
 

Summary of Contents for STM110C










































Reviews:

No comments

Brands by name

Popular brands

Load more brands