Page 5
Page 6
93-02056-01 Rev03
Page 1
Company Contact Information
Location:
930 Benecia Ave, Sunnyvale, CA 94085
Phone:
+1.650.964.1094
Web:
enlightedinc.com
Technical Support
FCC and Industry Canada Compliance Information
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions:
•
this device may not cause harmful interference, AND
•
this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by Enlighted Inc.
could void the user's authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
•
l'appareil ne doit pas produire de brouillage, ET
•
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
CE
This device complies with the essential requirements and other relevant
requirements of the R&TTE Directive (1999/5/EC) and Radio Equipment
Directive (RED) 2014/53/EU. The equipment is Class 1 radio equipment
which can be placed on the market and be put into service without
restrictions in accordance with article 1(3) of Commission Decision
2000/299/EC (Version July 2014).
Wireless protocol: IEEE802.15.4, Radio Freq: 2400 – 2483.5MHz,
RF TX output power (max): 3dBm
Wireless protocol: IEEE802.15.1, Radio Freq: 2400 – 2483.5MHz,
RF TX output power (max): 3dBm
Copyright © 2018 Enlighted Inc. All rights reserved.
All other brand or product names are trademarks of
their respective companies or organizations.
Micro Sensor
(SU-5E)
Installation Instructions
Model No. :
SU-5E-01
FCC ID:
AQQ-SU5E
IC:
10138A-SU5E
Micro Sensor and Carrier
Shipped Components
•
Enlighted Micro Sensor
Supplemental Components
•
Enlighted Sensor Cable
•
Enlighted Control Unit
Tools you may Need
•
7/8” Drill bit (1/2” knock out trade size)
•
Hand drill
LED Status
Description/Solution
LED not on
Check power and wiring
Green
blinking
Sensor is commissioned, working, and has
detected motion. If there is no motion in the
sensor’s field of view, the blinking will stop. Wave
your hands below the sensor to restart LED
blinking.
Red blinking
Sensor is not commissioned and has detected a
wiring issue. Check wiring to the Control Unit (CU)
and LED driver.
Red solid
Faulty sensor – replace sensor
Green solid
Sensor installed, initialized, and not
commissioned
–
waiting for discovery.
Blue solid
Sensor received a request to identify itself
LED Description
Step 1
: Connect one end of the sensor cable to the
Control Unit (CU). For wiring connections from the
Control Unit to the sensor, refer to the
Control Unit
Installation Guide
.
Connecting the Sensor Cable to the Control
Unit
Step 2
: Energize the luminaire and confirm that the
green LED is on solid.
R
005-101515