manualshive.com logo in svg

Engler DRILL-AIRE PLUS, Instruction Manual, Page: 19 / 30

Share
Download
Engler DRILL-AIRE PLUS Instruction Manual Download Page 19

SGII 

–  Doriot One - Piece Handpiece

Your unit may be equipped with the 

SGII 

–  Doriot One-Piece Handpiece instead of the E-TYPE LOW 

SPEED HANDPIECE, in this case use the following instructions.

The speed of the polishing head is proportional to the amount of pressure applied to the foot-switch 
pedal. Use low pressure to maintain a low speed.

SGII 

–  Doriot One-piece Handpiece

Technical Facts

SGII: Doriot One-piece Handpiece

Maximum RPM: 20,000 min

 

or 5,000 max

Attachment: accepts both handpiece burs and Doriot / U-type 
attachments

Air Requirements: Clean filtered moisture free air with recommended 
pressure of at least 45 psi.  

Do not exceed 60 psi

.

Operation

    

2

        1

Removing handpiece bur or Doriot attachment from Doriot Handpiece: 

Hold the handpiece in 

the left hand, depress housing ring toward the body of the handpiece while twisting ¼ turn to the right 
to open the chuck.

**Push then Pull the handpiece bur or attachment and remove from the chuck.

Forward / Reverse Speed:

 

Forward: 

Twist change ring fully clockwise

Reverse:

Twist  change ring fully conter-clockwise 

–

In mid position, handpiece will not 

operate

19

Summary of Contents for DRILL-AIRE PLUS































Reviews:

No comments