Operating Instructions: MIDI-Footcontroller Z-12: page 1
Congratulations on your choice, the ENGL Custom Footswitch Z-12. It is an ultra-modern, system-conform MIDI Footcontroller that let
you access 128 MIDI program locations (01 - 128). Program selection can be executed via any of the 16 specified MIDI channels (Poly
1-16). We equipped the ENGL MIDI Footcontroller with several practical features that facilitate utilitarian, comfortable handling:
12 buttons enable direct access to all program locations within a bank. Autocounting enables you to access banks that are located
greater distances from the currently active program (e.g. switching from Program Location 04 to Program Location 78) without
requiring a great deal of tap dancing. Simply hold the UP or DOWN buttons depressed until you scroll to the desired bank. Autostop
ensures the original bank is not bypassed so that you can quickly return to it if desired. The right display numeral flashes (01 position)
when the bank of the current Program Location is exited and lets you know that you must enter the one position for the newly selected
bank to activate the desired MIDI program location. Another especially handy feature of the ENGL Footcontroller: When you connect it
to the ENGL MIDI Interface Z-7 (new version with the small switch on the rear panel) or the ENGL Switcher Z-11, the Footcontroller is
supplied with power via the MIDI connector cable. In other words, you no longer need a separate power supply cord, only the MIDI
control cable that connects the Footcontroller to your setup.
Contents:
1. MIDI Footcontroller; 2. Operating Instructions
1."Program Location Number 0" Button:
When you press this button, the Footcontroller sends MIDI Program Location 10, 20, 30 ... to 120 in the respective bank.
In the first bank 01 to 09, this button is inactivate. In other words, when you press this button in the first bank, no Program Change
message is sent. This is indicated by a dash at the far right position of the the 7-segment display. After you power the Footcontroller up,
the ENGL logo runs across the 7-segment display. When you press a Program Location Number button, the corresponding Program
Location of the first bank is sent. The exception: 0. Here the dash appear in the right display.
2."
Pr
ogram location Number 1" Button:
When you press this button, the Footcontroller sends MIDI Program Location 01, 11, 21... to 121 in the respective bank.
3."Program location Number 2" Button:
When you press this button, the Footcontroller sends MIDI Program Location 02, 12, 22... to 122 in the respective bank.
4."Program location Number 3" Button:
When you press this button, the Footcontroller sends MIDI Program Location 03, 13, 23... to 123 in the respective bank.
5."Program location Number 4" Button:
When you press this button, the Footcontroller sends MIDI Program Location 04, 14, 24... to 124 in the respective bank.
6. "DOWN" Button, Bankdown (& MIDI Channel selection):
When you press this button, the first bank lower than the current bank is selected; the one position flashes to indicate that you
have exited the current bank and that you must enter the desired Program Location Number (0-9) before a new MIDI Program Location
is sent/activated. After you enter a Program Location Number, the selected MIDI Program Location appears in the display and the
one position illuminates continually. If you want to activate a more remote Program Location, you can either change locations in steps
by repeatedly pressing the button, or more comfortably by holding the button down to scroll continually.
MIDI Channel selection: After you power the Footcontroller up, MIDI Program Change commands are sent via Poly Channel 1. Use the
following procedure to select another MIDI Channel: Press the UP (7) and DOWN buttons simultaneously until the dot at the right
position of the display flashes. Now use the UP or DOWN buttons to select the desired Poly Channel. You can terminate Channel
Selection mode manually by selecting a MIDI Program Location. If you do not press a button, the Footcontroller automatically
terminates Channel Selection mode after an interval of approx. 10 seconds.
7. "UP" Button, Bankup (& MIDI Channel selection):
When you press this button, the first bank higher than the current bank is selected; the one position flashes to indicate that you
have exited the current bank and that you must enter the desired Program Location Number (0-9) before a new MIDI Program Location
is sent/activated. After you enter a Program Location Number, the selected MIDI Program Location appears in the display and the
one position illuminates continually. If you want to activate a more remote Program Location, you can either change locations in steps
by repeatedly pressing the button, or more comfortably by holding the button down to scroll continually.
MIDI Channel selection: After you power the Footcontroller up, MIDI Program Change commands are sent via Poly Channel 1. Use the
following procedure to select another MIDI Channel: Press the UP and DOWN (6) buttons simultaneously until the dot at the right
position of the display flashes. Now use the UP or DOWN buttons to select the desired Poly Channel. You can terminate Channel
Selection mode manually by selecting a MIDI Program Location. If you do not press a button, the Footcontroller automatically
terminates Channel Selection mode after an interval of approx. 10 seconds.
1
2
3
4
5
6
7
8
9
11
10
12
13
14
15
0
1
2
3
4
DOWN
MIDI Footcontroller
S
ERIAL
N
UMBER
5
6
7
8
9
UP
P
OWER
S
UPPLY
7-14 Volts AC
9-20 Volts DC
300 mA
TO SELECT
MIDI CHANNEL 1-16
PRESS UP AND DOWN
PUSHBUTTON
AT THE SAME TIME
UNTIL THE RIGHT DOT
OF THE DISPLAY STARTS
BLINKING AND PUSH
UP OR DOWN TO SELECT
THE REQUIRED
CHANNEL.
BANK
M
IDI
O
UTPUT
MADE IN GERMANY
MIDI FOOTCONTROLLER
TYPE Z-12
1xx
