manualshive.com logo in svg

EnGenius ESR-300H, User Manual, Page: 7 / 97

Share
Download
EnGenius ESR-300H User Manual Download Page 7

 

[ pg. 7] 

 

Front Panel 

Components 

Description 

Power LED 

This LED goes ON when the power is being supplied to the router. 

WLAN LED 

This LED goes ON when the RF (wireless LAN) feature is enabled. 

WAN LED 

This LED goes ON when an Ethernet cable is connected to the router’s WAN port. 

LAN (1 – 4 ) LEDs 

These LEDs go ON when an Ethernet cable is connected to the corresponding router LAN port. 

WPS button 

Press 1-to 5 seconds to activate the router’s Wi-Fi Protected Setup (WPS) feature. 
Press 6-to-10 seconds to reboot the router. 
Press 11 seconds or longer to reset the router to its default settings. 

 

 

Back Panel 

Components 

Description 

LAN Ports (1 – 4) 

Use an Ethernet cable to connect each port to a computer on your Local Area Network (LAN). 

WAN /Internet Port  

Use an Ethernet cable to connect this port to a cable or DSL modem. 

DC-Jack (POWER) 

Connect the power adapter to this connector. 

Power Switch 

Turns the router on or off. 

Antenna Connector 

Interface for the antennas. 

Summary of Contents for ESR-300H


































































































Reviews:

No comments