background image

HE, DE & RE MANUAL 

IOM-26 

5 of 33 

Oct 12 R4

 

 

WARRANTY 

 

LIMITED WARRANTY

 ENGINEERED AIR will furnish without charge, F.O.B. factory, freight collect, 

replacement parts for, or repairs to products covered herein which prove defective in material or 
workmanship under normal and proper use for a period of twelve (12) months from the initial start-up or 
eighteen (18) months from the date of shipment, whichever expires sooner, provided the customer gives 
ENGINEERED AIR written notice of such defects within such time periods and provided that inspection by 
ENGINEERED AIR establishes the validity of the claim and all pertinent invoices have been  paid in full.  
The repairs or replacements will be made only when the complete product(s) or part(s) claimed to be 
defective are returned to ENGINEERED AIR or a depot designated by ENGINEERED AIR, transportation 
charges prepaid.  Repairs or replacements as provided for by this paragraph shall constitute fulfillment of 
all ENGINEERED AIR's obligations with respect to this warranty. The refrigerant charge is not included in 
any part of this warranty. This warranty does not apply to any products or parts thereof that have been 
subject to accident, misuse or unauthorized alterations, or where ENGINEERED AIR's installation and 
service requirements have not been met.   
 
The foregoing warranty is in lieu of all other warranties, express or implied.  ENGINEERED AIR specifically 
disclaims any implied warranty of merchantability and/or fitness for purpose.  Under no circumstances shall 
ENGINEERED AIR be liable to, nor be required to indemnify, Buyer or any third parties for any claims, 
losses, labour, expenses or damages (including special, indirect, incidental, or consequential damages) of 
any kind, resulting from the performance (or lack thereof) of this Agreement or the use of, or inability to use 
the goods sold hereunder, including, but not limited to, damages for delay, temporary heating/cooling 
costs, loss of goodwill, loss of profits or loss of use.  Furthermore, the parties agree that the Buyer's sole 
remedy under this Agreement shall be limited to the limited warranty set forth in the preceding paragraph 
relating to the repair or replacement of any defective goods.  Under no circumstances shall any claim or 
award against ENGINEERED AIR exceed the original contract price whether awarded through arbitration, 
litigation or otherwise.  
 
ENGINEERED AIR Warranty is void if: 
 
1. 

The unit is not installed in accordance with this manual.  

2. 

The start-up and operation of the unit is not performed in accordance with this manual.  

3. 

The unit is operated in an atmosphere containing corrosive substances.  

4. 

The unit is allowed to operate during building construction. 

5. 

The unit is allowed to operate in atmospheres where chlorine or chlorine compounds are present or 
which contain any contaminant (silicone, aluminum oxide etc.) that adheres to the spark ignition 
flame sensing probe. 

Summary of Contents for ENGINEERED AIR DE Series


































Reviews: