5
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Features:
6SHFLÀFDWLRQV
Operating voltage
a9$&9'&
Current draw
DW9'&
Standby
15mA
Keypress
30mA
Output 1 active
55mA
7RWDOPD[FXUUHQWGUDZ
90mA
Outputs
Form C
$#9'&
Tamper
P$#9'&
(JUHVVLQSXW
12*URXQG
Operating temperature
-4°~158° F (-20°~70° C)
Operating humidity
a1RQFRQGHQVLQJ
'LPHQVLRQVLQFOXGLQJEDFNER[
4
5⁄8
´[
7⁄8
´[
½
´[[PP
Weight
6-oz (170g)
•
a9$&9'&$XWRDGMXVWLQJRSHUDWLRQ
•
8SWRSRVVLEOHXVHUFRGHVa
•
8SWRaSRVVLEOHWHPSRUDU\YLVLWRU
codes, which can be programmed for one-
time or limited-time use (1~99 hours)
•
2XWSXW)RUP&UHOD\$#9'&PD[
•
Output can be programmed to activate for up
to 99,999 seconds (nearly 28 hours)
•
7DPSHURXWSXW1&'U\FRQWDFW
P$#9'&PD[
•
0RXQWVWRDVWDQGDUGVLQJOHJDQJEDFNER[
VXUIDFHPRXQWEDFNER[LQFOXGHG
•
All features are programmed directly from the
NH\SDG1RQHHGIRUDQH[WHUQDOSURJUDPPHU
•
((35200HPRU\SURWHFWVSURJUDPPHG
information in case of power loss
•
(JUHVVLQSXWOHWVXVHUVH[LWWKHSUHPLVHV
without keying in the code
Overview:
Parts List:
[.H\SDG
[%DFNER[
[,QVWDOODWLRQVFUHZV
[0RXQWLQJVFUHZV
['LRGH
[0DQXDO
20
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the User Code Entry Mode (continued):
Programming the Keypad Sounds:
Some of the keypad sounds can be programmed off:
•
.H\SDGDXGLEOHPRGH±$OOWKHNH\SDG¶VVWDWXVEHHSVDUHHQDEOHG
•
Keypad silent mode – The successful key entry beep (1 beep) and the unsuccessful user code
entry beeps (5 beeps) are disabled. However, the warning and power-up delay beeps remain
DFWLYH7KLVSURYLGHVIRUDTXLHWHUZRUNHQYLURQPHQW
To Program:
•
To enable keypad audible mode (default):
•
To enable keypad silent mode:
NOTE: This programming function only impacts the keypad sounds. It does not impact the output
UHOD\DFWLYDWLRQVRXQGVVHH³3URJUDPPLQJWKH2XWSXW5HOD\$FWLYDWLRQ6RXQGV´EHORZ
To Program:
•
For auto entry mode:
•
For manual entry mode (default):
NOTE: If the keypad was previously programmed for manual code entry mode and then is
UHSURJUDPPHGIRUDXWRHQWU\PRGHDQ\FRGHVZKRVHOHQJWKH[FHHGVWKHQXPEHURI
digits of the master code will no longer operate the keypad. However, if the keypad is
reprogrammed for manual entry mode, the longer codes will again operate the keypad.
Programming the Output Relay Activation Sounds:
The keypad output sounds can be programmed for one of three modes:
•
1REHHSV
– The keypad will not beep when the output is activated:
•
1-second beep (default) – The keypad will beep for 1 second when the output is activated:
•
2 short beeps – The keypad will beep twice when the output is activated:
NOTE: This programming function only impacts the output relay activation sounds. It does not
LPSDFWWKHNH\SDGVRXQGVVHH³3URJUDPPLQJWKH.H\SDG6RXQGV´DERYH
