ENFORCER Room Monitor
4
SECO-LARM U.S.A., Inc.
PIR Sensor Detection Angle:
Sample Application
Using a Magnetic Contact for Door Monitoring:
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
PITSW1
Order Part# 763-189%
MI_RM-R100-xxxQ_181119.docx
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2018 SECO-LARM U.S.A., Inc. All
rights reserved.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
FCC COMPLIANCE STATEMENT
FCC ID: K4ER100TLQ
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.
Transmitter terminals
100kΩ
DNO+
GND
SOP-
V+
SIP-
DNO+
GND
SOP-
V+
SIP-
N.O. Magnetic Contact
N.C. Magnetic Contact
The Room Monitor can be used in a variety of
situations to monitor room occupancy, or even
assist customers if used with a service button.
Receivers can also be paired with handheld
transmitters to reset the receivers after the
service button has been pushed, or to reset any
preset timers.
The transmitter's PIR sensor can detect movement up to
~16ft (5m). However, be sure to take into account the
height and angle at which the transmitter is mounted.
Refer to the diagrams to the right to help you decide the
best height, and orientation, to mount your Room Monitor
transmitter.
16' (5m)
8' (2.5m)
x
Side view
41°
-41°
PIR Sensor
x
Top view
y
-47°
47°
8'
(2.5m)
16'
(5m)
y
Door monitoring should only be used for
applications where the door being monitored
is usually kept open.
If an N.C. magnetic contact is being used to
monitor the door then a 100kΩ resistor
(not included) should be installed between
the voltage and door contact inputs.
RM-R100-R2Q
RM-R100-RB1Q
1
2
RM-R100-TBQ
RM-R100-TLQ
1
2
Room 1 occupied
Room 2 empty
1
2
®
Room Monitor
Manual
Features:
PIR Sensor detects motion
(programmable ON/OFF via jumper)
Phototransistor detects light
(programmable ON/OFF via jumper)
Door sensor input on transmitter for
door monitoring
Can be programmed to flash and/or sound*
after a set amount of time
Service button connections available**
Suitable to use in restrooms, fitting rooms,
etc. to monitor occupancy
Receiver can be paired with 15
Transmitters per channel
Transmitter can transmit to unlimited
number of receivers
Compatible with all ENFORCER
433.92MHz transmitters
*Buzzer available on RM-R100-RB1Q only.
**RM-R100-TLQ and RM-R100-RB1Q only.
