ENFORCER
PoE (Power over Ethernet) Surge
2
Bandwidth
Maximum input
Insertion loss
Return loss
Frequency response
Insulation resistance
Maximum surge voltage
Discharging current
Surge life
Surge protection time
Surge resistance
Signal passing
capability
Breakdown voltage
Clamping voltage
Power passing capability
Connector
In
Out
Impedance
Dimensions
Weight
Material
Operating temperature
Introduction:
The ENFORCER PoE (Power over Ethernet) Surge Protector is a passive device that helps protect
sensitive networking equipment from power surges. The device can be deployed in new
installations or added to existing ones.
The ENFORCER PoE Surge Protector should be installed between the PoE hub and a networked
device to protect against surges that could damage the equipment.
NOTE
: For the best protection, installing two surge protectors is recommended:
the network cable.
Specifications:
Overview:
Protected End
3½” (88mm)
3” (75mm)
1”
(25mm)
Mounting Tab
To
Cat5e/6
Cable
Top View
Surge
Protector
SECO-LARM U.S.A., Inc.
Up to 68MHz
58Vp-p
<0.2dB
16dB@100H
Up to 3dB@68MHz
10,000MH
Up to 4 kV
400A
30000 surges@4 kV
1ns
0H
58V
77V
45W
RJ45
RJ45
42Ω
3½"x1"x1" (88x26x25 mm)
2.8-oz (80g)
Aluminum
-40°~185° F (-40°~85° C)
The ENFORCER PoE (Power over Ethernet) Surge Protector is a passive device that helps protect
sensitive networking equipment from power surges. The device can be deployed in new
The ENFORCER PoE Surge Protector should be installed between the PoE hub and a networked
device to protect against surges that could damage the equipment.
: For the best protection, installing two surge protectors is recommended: one at each end of
Unprotected End
1” (25mm)
1” (25mm)
Grounding
Wire
ENFORCER
PoE (Power over Ethernet)
SECO-LARM U.S.A., Inc.
1x PoE Surge Protector
2x Mounting Screws
1.
Each of the two PoE Surge Protectors should be mounted as close as possible to the device
be protected.
2.
Detach the existing Cat5e/6 cables from the devices to be protected (su
Camera) and attach them to end of their corresponding PoE Surge Protector marked “Cable End.”
3.
Prepare and connect an additional Cat5e/6 cable to each device to be protected and to the end of
Surge Protector marked “Equipment End.” For best protection,
possible to connect the PoE Surge Protectors and the protected device
should not cross unprotected cables.
4.
Connect the ground wires from the PoE Surge Protectors to earth ground.
single ground point and the protected device should be isolated from ground.
Protecting a Single Device:
1.
The PoE Surge Protector should be mounted as close as possible to the device that
2.
Detach the existing Cat5e/6 cable from the device to be protec
Protector marked “Cable End.”
3.
Prepare and connect an additional Cat5e/6 cable to the device
Surge Protector marked “Equipment End.” For best protection, this cable should be the shortest length
possible to connect the PoE Surge Protector and the protected device.
should not cross unprotected cables.
4.
Connect the ground wire from the PoE Surge Protector to earth ground.
ground point and the protected device should be isolated from ground.
Protecting Multiple Devices:
NOTE
: These instructions assume that 2 PoE devices have already been connected together.
IP Camera
(Protected)
PoE Surge
Protector
To ground
Shortest Possible
Cat5e/6 cable
Cat5e/6 cable
Protected End
Unprotected End
Unprotected End
To ground
PoE Surge
Protector
PoE Surge
Protector
Cat5e/6 cable
Protected End
IP Camera
(Protected)
Shortest
Possible Cat5e/6
cable
Installation:
Parts List:
PoE (Power over Ethernet)
Surge
Protector
3
2x Plastic Wall Anchors
should be mounted as close as possible to the devices that are to
protected (such as a PoE switch and IP
PoE Surge Protector marked “Cable End.”
device to be protected and to the end of its PoE
Surge Protector marked “Equipment End.” For best protection, these cables should be the shortest length
and the protected devices. In addition the protected cables
to earth ground. The system should use a
single ground point and the protected device should be isolated from ground.
The PoE Surge Protector should be mounted as close as possible to the device that is to be protected.
otected and attach it to end of the PoE Surge
vice to be protected and to the end of the PoE
rked “Equipment End.” For best protection, this cable should be the shortest length
possible to connect the PoE Surge Protector and the protected device. In addition the protected cables
PoE Surge Protector to earth ground. The system should use a single
ground point and the protected device should be isolated from ground.
devices have already been connected together.
PoE Switch
(Not Protected)
Cat5e/6 cable
Protected End
Shortest
Possible Cat5e/6
cable
PoE Switch
(Protected)
PoE Surge
Protector
