ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog UFO Camera
4
SECO-LARM U.S.A., Inc.
The screen is blank.
•
Check that the camera is powered up.
•
Check that the power supply's polarity is correct.
•
Check that the monitor is powered up.
•
Check that the video cable connecting the camera to the monitor is
connected properly.
The screen image is dim.
•
Clean the lens using a soft, clean cloth.
•
Check that the light source is adequate.
The screen image has poor
contrast.
•
Adjust the monitor's contrast knob.
•
Change the position of the camera.
The screen image flickers.
•
Change the position of the camera, check cables and format setting.
The screen image is distorted.
•
Change the position of the camera, check cables and format setting.
The camera case is hot.
•
Check that the correct power supply is in use.
®
PICSN4
MI_EV-Y6201-A3WQ_161020a.docx
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be
held responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Troubleshooting:
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric
shock. Do not open the case of this device, as there are no user-serviceable components inside.
Do not cut any wires as the warranty will be voided.
Surface-mounting allows for a quick and easy installation while
maintaining a low-profile appearance.
Diameter: 4
5
/
16
” (109mm)
Height (with camera): 2
3
/
8
" (60mm)
Optional Surface-Mount Bracket
(Sold separately)
:
EV-6640SWQ
