ENFORCER CCD B
ULLET
C
AMERA
Manual
ENFORCER CCD B
ULLET
C
AMERA
Manual
Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Automatic gain control
Power source
Power consumption
Storage temperature
Operating temperature
Dimensions (inc. cord mounting)
Weight
EV-1324C12 (NTSC)
EV-1354C12 (PAL)*
Color camera
Sharp
380 TV lines
1/4” CCD
512 x 492 pixels (NTSC)
512 x 582 pixels (PAL)*
2:1 interlace
V: 59.94Hz, H: 15.734KHz (NTSC)
V: 50Hz, H: 15.625KHz (PAL)*
Internal
1V pp composite output, 75ohms
F2.0, 3.6mm (lens included)
1.0 lux
0.45
>48dB
Auto Electronic Shutter
1/60~1/100,000 sec. (NTSC)
1/50~1/100,000 sec. (PAL)*
auto
auto
12VDC
125mA
22°~140° F (-30°~60° C)
14°~113° F (-10°~45° C)
3
3
/
16
” x
7
/
8
” (81 x 22mm)
2.8 oz. (80g)
EV-1323B12 (EIA)
EV-1353B12 (CCIR)*
B/W camera
Samsung
420 TV lines
1/3” CCD
510 x 492 pixels (EIA)
500 x 582 pixels (CCIR)*
2:1 interlace
V: 59.94Hz, H: 15.734KHz (EIA)
V: 50Hz, H: 15.625KHz (CCIR)*
Internal
1V pp composite output, 75ohms
F2.0, 3.6mm (lens included)
0.1 lux
0.45
>48dB
Auto Electronic Shutter
1/60~1/100,000 sec. (EIA)
1/50~1/100,000 sec. (CCIR)*
auto
auto
12VDC
125mA
22°~140° F (-30°~60° C)
14°~113° F (-10°~45° C)
3
3
/
16
” x
7
/
8
” (81 x 22mm)
2.8 oz. (80g)
Parts List
1 x Bullet camera
1 x Mounting bracket
3 x Mounting screws
3 x Screw anchors
1 x Manual
BEFORE STARTING
1. Do not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.
2. Do not point the camera at the sun. Heat could damage the
camera, even when not in use.
3. Do not mount the camera in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.*
INSTALLATION
1. Run a 12VDC power supply wire and a video cable with a male
BNC connector through the wall to where the camera is to be
mounted (if necessary).
2. Screw the bracket into the back of the camera. Make sure the
adjustment plate is on the plastic screw between camera and
bracket.
3. Temporarily connect the camera to the 12VDC power supply.
4. Temporarily connect the camera’s female BNC connector to the
video cable’s male BNC connector.
5. While watching the monitor, hold the camera bracket against the
wall by hand where it is to be mounted, then twist the camera
until it is certain that this mounting location is correct. Use a
pencil to mark the location of the three screw holes in the
bracket.
6. Disconnect the 12VDC power supply and video cable.
Specifications
A. Camera
B. Bracket
C. DC jack
D. BNC connector (female)
E. Thumb screw
F. Adjustment plate
G. Mounting screws (3)
H. Screw anchors (3)
A
4. Do not open or disassemble the camera. There are no user-
serviceable parts inside.
5. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic
fields close to the display CRT, especially when the monitor is
turned on or during de-Gaussing, which occurs automatically
with many monitors when the monitor is turned on.
7. Mount the bracket to the wall using the three included mounting
screws. If the wall is made of dry wall, brick, or similar material,
it may be necessary to use the three included screw anchors.
8. Reconnect the 12VDC power supply and video cable. Turn the
monitor on, and make sure the camera is sending the proper
video signal.
9. Adjust the camera angle:
(a) Loosen and tighten the bracket’s thumb screw to turn the
camera and change its angle relative to the bracket. This
ensures the camera is pointing in the right direction.
(b) Loosen and tighten the adjustment plate to rotate the camera
on its axis. This rotates the angle of the video image.
10.Tighten the bracket’s thumb screw and the adjustment plate so
that the camera does not move, but not so tight that it cracks
the case or bracket.
11.Do a final test of the video camera and monitor.
B
D
C
E
F
G
H
2” (50.5mm)
2” (50mm)
3” (76.5mm)
7
/
8
” (22mm)
19”, 50cm
cords
*Note: CCIR/PAL cameras available by special request only.
