ENFORCER CCD D
OME
C
AMERA
Manual
ENFORCER CCD D
OME
C
AMERA
Manual
Parts List:
1 x Dome camera
4 x Mounting screws
4 x Drywall anchors
1 x Manual
Focus
Lock Screw
Dome
Base
DC Jack
BNC(F) Connector
Support Bracket
INSTALLATION
1. Remove the dome. Be careful not to scratch the dome. DO
NOT TOUCH ANY OF THE COMPONENTS INSIDE THE DOME.
2. Connect the camera to a video monitor via the video cable.
3. Temporarily connect the camera to a 12VDC power source.
Do not cut the power jack or video jack, as warranty will
be voided.
4. Hold the base of the dome camera with your hand against the
ceiling, and try various locations and angles while watching
the video monitor to find the location which offers the best
protection. Mark that location with a pencil.
Note:
The ENFORCER dome camera is equipped with multi-axis
Gimbal bracket which will make it applicable for both wall and
ceiling.
5. For wall-mounting applications
—
Take out the 2 screws and
turn the lens 90
o
clockwise until the wire harness is adjacent
to the mounting bracket. Replace the 2 screws to
secure it. See Fig. 1.
6. Run a hidden, permanent video cable from the monitor
to the mounting location.
7. Run a hidden cable from a 12VDC power supply to the
mounting location.
8. Connect the two cables to the dome camera.
9. Mount the base to the ceiling at the selected location
with the four mounting screws.
10. Make any necessary adjustments to the horizontal and
vertical angles of the camera itself while checking the
image in the video monitor.
11. Replace the dome, taking care not to touch the camera
or scratch the dome.
12. Test the camera again under the exact lighting
conditions under which it is expected to be used.
3
1
/
2
” (88mm)
SIDE VIEW
BOTTOM VIEW
2
1
/
4
” (57mm)
3
1
/
2
” (88mm)
Important:
Do not cut DC jack. Use
SECO-LARM’s optional
EVA-F5521-3 Pigtail Connector for
easy installation and serviceability.
Lens
Wire harness
BEFORE STARTING
1. This product was designed for indoor use only. Do not mount
the CCTV camera where it is exposed to rain or other moisture,
or in humid or dusty places.
2. Do not point the CCTV camera at the sun. Heat could damage
the camera, even when not in use.
3. Do not mount the CCTV camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.*
4. Do not disassemble the lens or circuit board. There are
no user-serviceable parts inside.
5. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromag-
netic fields close to the display CRT, especially when the
monitor is turned on or during de-Gaussing, which
occurs automatically with many monitors when the
monitor is turned on.
Window
Camera
Dimensions:
EV-122B-4 (EIA)
EV-125B-4 (CCIR)
B/W camera
1/3” CCD, A1 PROs
N/A
EV-1223C12 (NTSC)
EV-122C-2 (NTSC)
EV-1253C12 (PAL)
EV-125C-2 (PAL)
Color camera
1/3” CCD, Sony
AWB
110mA
Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens
Viewing Angle
*
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Gain control
White Balance
D/A Bits
Power source
Power consumption
Operating temperature
Dimensions
Specifications
420 TV lines
512 x 492 pixels (NTSC / EIA)
512 x 582 pixels (PAL / CCIR)
2:1 interlace
Internal
1V pp composite output, 75 ohms
EV-1223C12 / EV-122B-4 (4.3mm)
EV-1253C12 / EV-125B-4 (4.3mm)
EV-122C-2 / EV-125C-2 (2.9mm)
EV-1223C12 / EV-122B-4 (78
o
)
EV-1253C12 / EV-125B-4 (78
o
)
EV-122C-2 / EV-125C-2 (120
o
)
0.1 lux
0.45
>48dB (AGC off)
Auto Electronic Shutter (AES)
1/60~1/100,000 sec. (NTSC / EIA), 1/50~1/100,000 sec. (PAL / CCIR)
Auto & Manual
Auto
10
12VDC
14°~140° F (-10°~60° C)
3
1
/
2
” x 2
1
/
4
” (88 x 57 mm)
* All viewing angles are approximate
100mA
Screw
Wire
Harness
Screw
Support
Bracket
Support
Bracket
Support
Bracket
Wire
Harness
90
o
oo
oo
Fig. 1 — For wall mounting. Remove the 2 screws and turn the lens 90
o
oo
oo
clockwise
until the wire harness is adjacent to the support bracket, then replace the 2 screws
to secure it.
Important:
Do not cut DC Jack or Video Jack
as warranty will be voided.
Lens
