background image

About OutBack Power Technologies 

Outßack Power Technologies is a leader in advanced energy conversion technology. 

Outßack products include true sine wave inverter/chargers, maximum power point tracking 

charge controllers, and system communication components, as weil as circuit breakers, 

batteries, accessories, and assembled systems. 

Disclaimer 

UNLESS SPECIFICALL Y AGREED TO IN WRITING, OUTBACK POWER TECHNOLOGIES: 
(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY

TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER

DOCUMENTATION.

(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WH ETHER DIRECT,

INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF

SUCH IN FORMATION. THE USE OF ANY SUCH IN FORMATION WILL BE ENTIREL Y AT THE

USER'S RISK.

Notice of Copyright 

GS-IOB-230VAC Installation lnstructions© February 2014 by Outßack Power Technologies. 

All Rights Reserved. 

Trademarks 

Outßack Power, the Outßack Power logo, FLEXpower ONE, Grid/Hybrid, and FLEXgrid are 

trademarks owned and used by Outßack Power Technologies, lnc. These trademarks may 

be registered in the United States and other countries. 

Date and Revision 

February 2014, Revision A 

Part Number 

900-0146-01-00 REV A

Worldwide Co

r

porate Offices

 

Alpha 

and Outback Energy

 

GmbH 

reserves the right to make changes to the products and information contained in this document without notice.

 

Copyright © 20

20

 Alpha 

and Outback Energy GmbH

. All 

Rights reserved. 

Headquarter Germany

Hansastrasse 8

D-91126 Schwabach

Tel: +49 9122 79889 0

Fax: +49 9122 79889 21

Mail: [email protected]

France and Benelux 

fbnl

@alpha-outback-energy.com

Spain 

[email protected]

For 

more

 information please visit 

www.alpha-outback-energy.com

Russia

russia

@alpha-outback-energy.com

Africa

[email protected]

Eastern Europe

[email protected]

Middle East

[email protected]

Summary of Contents for OutBack POWER ALPHA OUTBACK ENERGY GS-IOB-230VAC










Reviews: