4
5
6
This device is warranted to be free of material and workmanship defects for 2 years from the
date of purchase. Original receipt or proof of purchase from an authorized retailer must be
presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc.
Warranties from other Enerlites products may vary. This warranty is nontransferable and does
not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse,
abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted
by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer
of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites
has been advised of the possibility of such damages. Enerlites’ total liability under this or any
other warranty, express or implied, is limited to repair, replacement or refund. Repair,
replacement or refund are the sole and exclusive remedies for breach of warranty or any other
legal theory.
© 2016 Enerlites Inc.
CA, U.S.A.
WWW.ENERLITES.COM
0103170082
-0
2
TROUBLESHOOTING
The
switch
buttons
are
not functional
Check if the device is
wired
properly. Th
is
device requires a
NEUTRAL
wire for
operation.
Often the WHITE wire is used as a LOAD wire. Be sure to test ALL
wires. Also make sure that the HOT and LOAD wires are not reversed.
Press the
L
ight or
the
F
an button
:
•
•
•
If the load does not work and the indicator light does
not flash
.
T
URN
OFF
the
power at the circuit breaker then check wire
connections. Confirm
that
the
NEUTRAL
wire is connected
and
Black
AND
Blue leads are connected to
the
incoming
H
OT
wire.
If the
humidity sensor does not
turn on
the fan.
Change the humidity level to match the appropriate condition or m
anually
turn ON the fan, after
2
0
minutes the humidity sensor will be operational.
If the light does not turn on but the indicator light is flashing
.
The switch is in Vacancy Mode.
Programming Example
:
Change the time delay of the switch from
10
minutes
to
20
minutes as follows:
1.
Press and hold
the light button for eight seconds. The green LED light
will come on solid.
2.
Press the light button once for
Function 1:
Time Delay.
3.
The green LED light will now flash once every
2
seconds indicating the
current time delay, which is at
10
minutes
.
Press the light button
two times
to choose
Setting 2
(
20
minutes
)
.
The
green LED light now will flash
es
two times
every 2 seconds indicating
the new time delay of
20
minutes.
Press and Hold
the light button for eight seconds. The LED light will
flash 3 times indicating that the settings are saved
and the l
oad
will turn
OFF.
STEP 1:
Enter Programming Mode
•
Press and hold the light button for eight seconds until the solid green LED
lights up (the LED will stay on). The sensor is now in programming mode.
STEP 2:
Choose the Function
•
Press the light button the same number of times as the Function Number you
would like to program.
o
After the last button is pressed the sensor will flash back the current
setting for that function10 times at two-second intervals. If no
selection has been made, the device will exit programming mode.
STEP 3:
Choose the Setting
•
Press the light button the same number of times as the Setting Number for
that function (For example in Function 1: Press the button 2 times to select
20
minutes
).
o
After the last button is pressed the sensor will flash back the current
setting for that function10 times at two-second intervals. If no
selection has been made, the device will exit programming mode.
STEP 4:
Save the Settings
•
Press and Hold the light button for eight seconds. The LED light will flash 3
times indicating that the settings are saved.
PROGRAMMING
During programming, ONLY the
Light Button
will be used. Pay close
attention to the
G
reen LED lights as it will flash
to indicate
successful programming steps.
The LED will also flash each time
the button is pressed while making the selections.
Once the
program is saved, the
load
will turn OFF.
After each step, there
are only
20 seconds to make the next
programming selection. If a selection has not been made, time will
expire and the LED light will flash 3 times and exit programming
mode.
There are 2 Programmable Functions:
•
Function 1:
Time Delay
•
Function 2:
Humidity Level
Factory default settings are indicated with (*)
Function 1
:
Time Delay for the light and fan
•
Setting 1:
15 seconds (*)
After 5 minutes, the switch will automatically set to 10 minutes
•
Setting 2:
20
minutes
•
Setting 3:
30
minutes
FUNCTIONS/SETTINGS
EXAMPLE
WARRANTY INFORMATION
Function 2
:
Humidity level (Humidity Range
45
% -
80
%)
•
Setting 1:
Low
humidity sensitivity
(requires little humidity to trigger)
•
Setting 2:
Medium humidity sensitivity(*)
•
Setting 3:
High
humidity sensitivity
(requires high humidity to trigger)
OPERATING INSTRUCTIONS Cont.
o
Fan: Auto On, Auto Off. The Fan will turn ON automatically when
preset humidity level is reached and automatically turn OFF when the
humidity level drops below the preset.
If the humidity level is higher than preset then the fan will continue to
run after a 5 minutes break.
When the manual button is used to turn ON, the fan will turn ON for
2
0 minutes and automatically turn OFF.
When the manual button is used to turn OFF before the
2
0 minutes,
the fan will turn OFF immediately and the humidity sensor will stop
detecting. Only when the manual button is used to t
u
rn ON again,
after
2
0
minutes the humidity sensor will be operational again.
