Energy Veritas V2.0C Owner'S Manual Download Page 5

Advanced Set Up 

PLACEMENT OF THE 
CENTER CHANNEL V2.0C

The center channel needs to be placed either above or

below the TV monitor, but as close to the TV as possible.

The center channel carries dialogue information which

should sound like it is emanating from the center of the

TV. If using a Rear Projection Television, then above is

probably your only choice.  If you have a front projection

system, than you have alternate choices of either stand

mounting, or placement on furniture, etc. 

When deciding on the center channel speaker placement,

it is important to place the speaker so that the edge of the

speakers' front is at the edge of the shelf or stand

supporting it. Unwanted diffraction would occur if the

center channel is situated too far back into a cabinet or

other surface with edges that could impede the dispersion

of the speaker.  

See Figure 1B.

PLACEMENT OF THE REAR CHANNEL 
V2.0R SPEAKERS

The Rear Channel V2.0R speakers are optimally placed on

either the sides of your listening area, or the rear walls.

The V2.0R has been designed with installation flexibility as

its key goal. The side firing mid-fill transducers coupled

with the front firing woofer and tweeter combine to

produce various levels and effects depending on the

speakers' location, and how the “SoundField

Management” System is adjusted. The following are

suggestions of where you can place your V2.0R speakers. 

See Figure 1B.

SIDE POSITION

The optimal placement for the V2.0R's on the side of the

room, would be beside the listening area, a few feet

behind the couch, at a height approximately 2/3 of the

wall height from the floor.  The “SoundField Management”

System can be adjusted in many different ways. Refer to

the separate section for adjusting the “SoundField

Management” System.

REAR POSITION

The rear wall can also be used for placement of the rear

V2.0R speakers. The optimum placement would be on

either side of the listening area, but not in the corners of

the room. Experimentation with the “SoundField

Management” System will yield many different results.

Refer to the separate section for adjusting the “SoundField

Management” System. 

CORNER POSITION

If you are limited to a corner placement of the rear

channel speakers, we have designed a special “SoundField

Management” mode for this purpose. It will turn off the

side firing mid-fill driver above the control panel. Please

notice that the two rear channel speakers are mirror-

imaged of each other. When mounting the speakers, be

sure to put the control panel facing the corner. This way

the corner facing mid driver will not emanate sound. The

other mid driver which faces out into the room, will

produce sound.  

OWNERS MANUAL

VERITAS

6

RIGHT

SIDE POSITION

LEFT MAIN

RIGHT MAIN

SUBWOOFER

CENTER

CHANNEL

LEFT

SIDE POSITION

REAR OR CORNER POSITION

FIGURE 1B

Summary of Contents for Veritas V2.0C















Reviews: