Pager Module Installation
Page 2
AW000924-B
7.
From the Thermostat main menu, navigate to the
Installer Setup
menu.
When the pager module is installed and working properly, the
Pager
option is displayed in the
Installer Setup menu. Use this option to access information about the pager module’s connection to
the network and other troubleshooting information.
Pager Module Signal Status
The thermostat cannot receive messages or DR events until it is provisioned using the CCDR website
provided by the electric utility.
After the pager module is provisioned, the link status indicator at the top right of the Temperature or
Energy home screen displays the status of the Foundation’s wireless uplink signal(s). The following
indicators can be displayed to the right of the signal strength bars:
•
F:
Thermostat is receiving communications from its server using the pager module.
•
D:
Thermostat is communicating with its server using both the pager module and a ZigBee
gateway (dual wireless uplinks).
•
Z:
Thermostat is communicating with its server using a ZigBee gateway.
Pager Link Information
Use the Pager menu’s
Link Info
option to display information such as connection status, pager radio signal
strength, and hardware/firmware version information. A two-digit confirmation code (CC) is displayed in
the bottom-right corner of the Link Info screen, verifying successful provisioning.
The first Link Info screen displays the current status of the pager module’s connection to the network:
Message
Description
CONNECTION
ACTIVE
Normal condition when working correctly.
Foundation is connected to and successfully communicating with the CCDR
server over the pager radio network.
SEARCHING FOR
NETWORK
The pager module is working but is unable to detect the pager network.
NETWORK LOST
The pager module is working and was previously connected to the pager
network, but is no longer communicating with the network.
PAGER HARDWARE
ERROR
There is a problem with the pager module related to its hardware or
configuration. Please contact technical support.
WAITING FOR
COMMISSION
The pager module is working, has detected the pager network, and is waiting
to be provisioned (commissioned).
WAITING FOR
BEACON
The pager module is connected to the pager network but is waiting for a
beacon signal from the pager network.
The Foundation cannot be provisioned until it receives the beacon signal.
For information on troubleshooting a pager module installation, see the Troubleshooting section in
Installation Guide for Energate Thermostats
.
Compliance Information
Product: Flex Pager USNAP Radio Module
Model: RM41F
Responsible Party: Energate Inc., 2379 Holly Lane, Suite
200, Ottawa, Ontario K1V 7P2, Canada. T.: 613-482-7928
This equipment is RoHS compliant.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the
interference, and (2) this device must accept any
following two conditions: (1) this device may not cause
interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Cet appareil numérique de la classe B est conforme à la
norme FCC 47 CFR Part 15.
