Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 22

Page: 22 / 144

Mounting

Waterpilot FMX21

Hauser

>7 (0.28)

A0018696

Unit of measurement mm (in)

Terminal box

Terminal strip

TMT72 temperature head transmitter

NOTICE

Incorrect connection!

‣

A distance of > 7 mm (28 in) must be maintained between the terminal strip and the

TMT72 temperature head transmitter.

5.8

Mounting the terminal strip for the Pt100 passive

(without TMT72)

If the FMX21 with optional Pt100 is supplied without the optional TMT72 temperature

head transmitter, a terminal strip is provided with the terminal box for the purpose of

wiring the Pt100.

WARNING

Explosion Hazard!

‣

The Pt100, as well as the terminal strip, are not designed for use in hazardous areas.

A0018815

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands