background image

Turbimax W CUS65

Installation

Hauser

7

3

Installation

3.1

Incoming acceptance, transport, storage

• Make sure the packaging is undamaged!

Inform the supplier about damage to the packaging. Keep the damaged packaging until the matter 
has been settled.

• Make sure the contents are undamaged!

Inform the supplier about damage to the delivery contents. Keep the damaged products until the 
matter has been settled.

• Check that the scope of delivery is complete and agrees with your order and the shipping 

documents.

• The packaging material used to store or to transport the product must provide shock protection 

and humidity protection. The original packaging offers the best protection. Also, keep to the 
approved ambient conditions (see "Technical data").

• If you have any questions, please contact your supplier or your sales center responsible.

3.2

Installation conditions

3.2.1

Dimensions

a0008995

Fig. 1: 

Dimensions dependend on the sensor version (see ordering information)

D

E

B

NPT ¾

A

G1

C

Ø40

(1.57)

145

(5.71)

142

(5.59)

60

(2.36)

154

(6.06)

147

(5.79)

mm (inch)

154

(6.06)

Summary of Contents for Turbimax W CUS65





















Reviews: