Endress+Hauser Topcal S CPC310 Operating Instructions Manual Download Page 116

Page: 116 / 176

Commissioning

116

Procedure

If you have not made any initial settings for local calibration, please make them in the "

Set up 1 > Calibration" menu.

Set the service switch to "Service" (vertical) or move the assembly into the Service position

Remove the sensor.

Clean the sensor before calibration.

Note!
• When measuring with PM (potential matching), the PM line also has to be immersed in the buffer

solution.

• If automatic temperature compensation is selected for calibration (ATC), the corresponding

temperature sensor must also be immersed in the buffer solution.

• The instrument switches automatically to Hold (factory setting) whenever it is calibrated.
• Press

to cancel the calibration. In the dialog field that follows, select "Yes, abort cal.".

The following section describes the calibration cycles for:

Calibration pH

• ""Manual data input"
• "Cal with manual buffer"
• "Cal with buffer table"
• "Cal with automatic buffer recognition"

Calibration, redox absolute

• "Data input absolute"
• "Calibration, absolute"

Calibration, redox relative

• "Data input absolute"
• "Data input relative"
• "Calibration, absolute"
• Calibration, relative

7.9.1

Calibration pH

Manual data entry

The values for sensor zero point and slope are entered manually.
Press

to start calibration.

Function

Options

Info

Note

Calibration with enter spec.
buffer

The type of local calibration selected in the
calibration settings is displayed.

Temperature

-20.0 ... 150.0

Factory setting

25.0

Specify the temperature at which calibration
takes place (only for "Cal with MTC").
Confirm with

Zero point

-2.00 ... 16.00 pH

Factory setting

7.00 pH

Enter the zero point of the electrode.
Confirm with

Slope

5.00 ... 99.00 mV / pH

Factory setting

59.16 mV/pH

Enter the slope of the electrode.
Confirm with

Calibration

Options
• Accept
• Cancel
• Repeat calibration

Ending calibration

Accept:

When you confirm with

, the new

calibration data are accepted.

Cancel:

The data are not accepted. Calibration

is not repeated.

Repeat calibration:

The data are rejected and

calibration is repeated.

Summary of Contents for Topcal S CPC310

















































































































































































Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands

Endress+Hauser Topcal S CPC310, Operating Instructions Manual

Search results

Summary of Contents for Topcal S CPC310

Reviews:

Related manuals for Topcal S CPC310

Brands by name

Popular brands