Endress+Hauser Proline Promag 55 Operating Manual Download Page 81 | Manualshive

Page: 81 / 130

background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

81

System Unit -
Length

AUTO - OOS

Use this parameter to select the unit for displaying the length of the
nominal diameter.

The unit you select here is also valid for:
Nominal diameter of sensor ("Sensor Data - Nominal Diameter",

Options:

MILLIMETER
INCH

Factory setting:

MILLIMETER (SI units: not for USA and Canada)
INCH (US units: only for USA and Canada)

Sys. - Install.
Direction Sensor

AUTO - OOS

Use this parameter to reverse the sign of the flow measured variable, if
necessary.

Options:

NORMAL FORWARD (flow as indicated by the arrow)
INVERSE REVERSE (flow opposite to direction indicated by the arrow)

Factory setting:

NORMAL FORWARD

!

Note!

Ascertain the actual direction of fluid flow with reference to the direction
indicated by the arrow on the sensor (nameplate).

Sys. - Flow Damping

AUTO - OOS

Use this function to set the filter depth of the digital filter. This reduces the
sensitivity of the measuring signal to interference peaks (e.g. high solids
content, gas bubbles in the fluid, etc.). The reaction time of the measuring
system increases with every increase in the filter setting. The damping acts
on all parameters and on all downstream function blocks.

User input:

0 to 15

Factory setting:

7

!

Note!

The system damping acts on all functions and outputs of the measuring
device.

Sys. - Integration
Time

AUTO - OOS

Use this function to view the set integration time.

The integration time defines the duration of internal totaling of the
induced voltage in the fluid (measured by the measuring electrode), i.e.
the time in which the measuring device records the true flow (afterwards
the magnetic field for the next integration is created from the opposite
pole).

User interface:

Max. 2-digit number: 1 to 65 ms

Factory setting:

5 ms

"Flow" Transducer Block/base index 1400

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
79
80
81
82
83
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: AbleNet Pages: 9

CSL Elite Racing Wheel

Brand: FANATEC Pages: 2

Brand: FANATEC Pages: 8

Brand: FANATEC Pages: 35

Brand: GCE Pages: 16

Brand: GCC Technologies Pages: 12

Brand: jbc Pages: 4

Brand: jbc Pages: 4

Brand: jbc Pages: 8

Brand: Kathrein Pages: 7

Brand: Kathrein Pages: 2

Brand: Patton electronics Pages: 12

Brand: Q'STRAINT Pages: 10

Brand: PASCO Pages: 8

Brand: Olympus Pages: 172

Brand: ZEPP Pages: 36

FleetMaster Air FW8 Series

Brand: SAF-HOLLAND Pages: 20

Brand: Takex Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands