Endress+Hauser Proline Promag 55 Operating Manual Download Page 44

Page: 44 / 130

7 Block BASIC FUNCTION

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

7.2

Group PROCESS PARAMETER

7.2.1

Function group CONFIGURATION

BASIC FUNCTION

⇒

FOUNDATION FIELDBUS GAA

⇓

PROCESS PARAMETER

GIA

⇒

CONFIGURATION

640

Function description

BASIC FUNCTION

→

PROCESS PARAMETER

→

CONFIGURATION

ASSIGN LOW FLOW CUT
OFF
(6400)

Use this function to assign the switch point for the low flow cut off.

Options:

OFF
MASS FLOW
VOLUME FLOW

Factory setting:

VOLUME FLOW

ON-VALUE LOW FLOW
CUT OFF
(6402)

Use this function to enter the switch-on point for low flow cut off.

Low flow cut off is active if the value entered is not equal to 0. The sign of the flow value
is highlighted on the display to indicate that low flow cut off is active.

User input:

5-digit floating-point number [unit]

Factory setting:

Nominal diameter and country dependent

→

Page 123 ff.

Note!

The appropriate unit is taken from the function UNIT VOLUME FLOW (0402) or UNIT
MASS FLOW (0400) (

→

Page 12 or Page 11).

OFF-VALUE LOW FLOW
CUT OFF
(6403)

Use this function to enter the switch-off (

) point for low flow cut off.

Enter the switch-off point as a positive hysteresis (

) from the switch-on point (

User input:

Integer 0 to 100%

Factory setting:

50%

A0003882

= switch-on point,

= switch-off point

Low flow cut off is switched on

Low flow cut off is switched off (a + a

⋅

Hysteresis value: 0 to 100%

■

Low flow cut off active

Flow

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands