manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 99

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

99

3.4  

"Input" submenu

Navigation

 Expert → Input

‣

Input

‣

Current input 1 to n

→   99

‣

Status input 1 to n

→   102

3.4.1  

"Current input 1 to n" submenu

Navigation

 Expert → Input → Current input 1 to n

‣

Current input 1 to n

Terminal no. (1611–1 to n)

→   99

Signal mode (1610–1 to n)

→   100

Current span (1605–1 to n)

→   100

0/4 mA value (1606–1 to n)

→   100

20 mA value (1607–1 to n)

→   101

Failure mode (1601–1 to n)

→   101

Failure value (1602–1 to n)

→   102

Terminal no.

Navigation

 Expert → Input → Current input 1 to n → Terminal no. (1611–1 to n)

Description

Displays the terminal numbers used by the current input module.

User interface

• Not used

• 24-25 (I/O 2)

• 22-23 (I/O 3)

Additional information

"Not used" option

The current input module does not use any terminal numbers.

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands