Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 186

Page: 186 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

186

Hauser

3.8.6

"Sens. electronic" submenu

Navigation

 Expert → Diagnostics → Sens. electronic

‣

Sens. electronic

Software rev. (0072)

→  186

Build no. softw. (0079)

→  186

Bootloader rev. (0073)

→  186

Software rev.

Navigation

 Expert → Diagnostics → Sens. electronic → Software rev. (0072)

Description

Use this function to display the software revision of the module.

User interface

Positive integer

Build no. softw.

Navigation

 Expert → Diagnostics → Sens. electronic → Build no. softw. (0079)

Description

Displays the software build number of the module.

User interface

Positive integer

Bootloader rev.

Navigation

 Expert → Diagnostics → Sens. electronic → Bootloader rev. (0073)

Description

Displays the bootloader revision of the software.

User interface

Positive integer

Summary of Contents for Proline Promag 300

















































































































































































































































































Search results

Summary of Contents for Proline Promag 300

Reviews:

Related manuals for Proline Promag 300

Brands by name

Popular brands

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Search results

Summary of Contents for Proline Promag 300

Reviews:

Related manuals for Proline Promag 300

Brands by name

Popular brands