manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 104

Description of device parameters

Proline Promag 300 Modbus RS485

104

Hauser

Active level

Navigation

 Expert → Input → Status input 1 to n → Active level (1351–1 to n)

Description

Use this function to determine the input signal level at which the assigned function is

activated.

Selection

• High

• Low

Factory setting

High

Response time

Navigation

 Expert → Input → Status input 1 to n → Response time (1354–1 to n)

Description

Use this function to enter the minimum time period for which the input signal level must

be present before the selected function is activated.

User entry

5 to 200 ms

Factory setting

50 ms

3.5  

"Output" submenu

Navigation

 Expert → Output

‣

Output

‣

Curr.output 1 to n

→   104

‣

PFS output 1 to n

→   118

‣

Relay output 1 to n

→   138

‣

Double pulse out

→   145

3.5.1  

"Current output 1 to n" submenu

Navigation

 Expert → Output → Curr.output 1 to n

‣

Curr.output 1 to n

Terminal no. (0379–1 to n)

→   105

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands