Endress+Hauser Micropilot FMR56 Operating Instructions Manual Download Page 148

Page: 148 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

148

Hauser

Selection

SI units

• STon

• t

• kg

• cm³

• dm³

• m³

• hl

• l

• %

US units

• lb

• UsGal

• ft³

Imperial units

impGal

Custom-specific units

Free text

Factory setting

Additional information

The selected unit is only used to be indicated on the display. The measured value is

not

transformed according to the selected unit.

It is also possible to configure a distance-to-distance linearization, i.e. a

transformation from the level unit to a different distance unit. To do so, select the

Linear

linearization mode. In order to define the new level unit, select the

Free text

option in the

Unit after linearization

parameter and enter the required unit into the

Free text

parameter (→  148).

Free text



Navigation

 Setup → Advanced setup → Linearization → Free text

Prerequisite

Unit after linearization (→  147)

Free text

Description

Enter unit symbol.

User entry

Up to 32 alphanumerical characters (letters, numbers, special characters)

Factory setting

Free text

Level linearized

Navigation



Setup → Advanced setup → Linearization → Level linearized

Description

Displays linearized level.

Additional information

The unit is defined by the

Unit after linearization

parameter →  147.

Summary of Contents for Micropilot FMR56







































































































































































































Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands

Endress+Hauser Micropilot FMR56, Operating Instructions Manual

Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands