Endress+Hauser Micropilot FMR56 Operating Instructions Manual Download Page 88 | Manualshive

Page: 88 / 198

background image

Commissioning (block-based operation)

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

88

Hauser

12.8.1 Groups of events

The diagnostic messages are classified into 16 groups according to the

source

and

severity

of the respective event. A

default diagnostic category

is allocated to each group. Each

group is also represented by one bit of the allocation parameters.

Severity of the
event

Default diagnostic category Source of the

event

Bit

Events within the group

Highest severity

Failure (F)

Sensor

31

• F003: Broken probe detected
• F046: Build-up detected
• F083: Memory content
• F104: HF cable
• F105: HF cable
• F106: Sensor

Electronics

30

• F242: Software incompatible
• F252: Modules incompatible
• F261: Electronic modules
• F262: Module connecting
• F270: Main electronic failure
• F271: Main electronic failure
• F272: Main electronic failure
• F273: Main electronic failure
• F275: I/O-Modul failure
• F276: I/O module failure
• F282: Data storage
• F283: Memory content
• F311: Electronic Failure

Configuration 29

• F410: Data transfer
• F435: Linearization
• F437: Configuration incompatible
• F482: Block in OOS

Process

28

• F803: Current loop 1
• F825: Current loop 1
• F936: EMC interference
• F941: Echo lost

• F970: Linearization

1)

This event can be removed from the group in order to define its behavior individually; see section
"Configurable area".

Severity of the
event

Default diagnostic category Source of the

event

Bit

Events within the group

High severity

Function check (C)

Sensor

27

not used in Micropilot

Electronics

26

not used in Micropilot

Configuration 25

• C411: Up-/download
• C484: Simulation failure mode
• C485: Simulation measured value
• C492: Simulation frequency

output

• C493: Simulation pulse output
• C494: Switch output simulation
• C495: Simulation block output
• C585: Simulation distance
• C586: Record map

Process

24

not used in Micropilot

Severity of the
event

Default diagnostic category Source of the

event

Bit

Events within the group

Low severity

Out of specification (S)

Sensor

23

not used in Micropilot

Electronics

22

not used in Micropilot

«
...
86
87
88
89
90
...
»

Summary of Contents for Micropilot FMR56







































































































































































































Reviews:

No comments

Related manuals for Micropilot FMR56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands