Endress+Hauser Liquiphant FTL64 Operating Instructions Manual Download Page 50

Page: 50 / 64

Accessories

Liquiphant FTL64

Hauser

In accordance with German law regulating the use of batteries (BattG §28 Para 1

Number 3), this symbol is used to denote electronic assemblies that must not be disposed

of as household waste.

Accessories

13.1 Device Viewer

All the spare parts for the device, along with the order code, are listed in the

Device Viewer

(

www.endress.com/deviceviewer

13.2 Test magnet

Order number: 71437508

A0039209

 43

Test magnet

13.3 Weather protection cover for dual compartment

housing, aluminum

• Material: stainless steel 316L

• Order number: 71438303

81 (3.19)

103 (4.06)

102.5 (4.04)

73.5 (2.89)

135 (5.31)

228.9 (9.01)

136.4 (5.37)

!65 (2.56)

92.5 (3.64)

A0039231

 44

Weather protection cover for dual compartment housing, aluminum. Unit of measurement mm (in)

Summary of Contents for Liquiphant FTL64

































































Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands

Endress+Hauser Liquiphant FTL64, Operating Instructions Manual

Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands