Endress+Hauser Liquiphant FTL64 Operating Instructions Manual Download Page 37

Page: 37 / 64

Liquiphant FTL64

Commissioning

Hauser

Bluetooth module VU121 (optional)

Functions

• Connection via COM interface: Bluetooth module for device diagnostics via a smartphone

app or tablet app

• Display the battery status via app when used with electronic insert FEL68 (NAMUR)

• User guidance (wizard) for SIL/WHG proof testing

• Visible in the livelist 10 s seconds after the Bluetooth search commences

• Data can be read from the Bluetooth module 60 s after the supply voltage is switched on

• Display of the current vibration frequency and the switching state of the device
The yellow LED flashes when the Bluetooth module is connected to another Bluetooth

device, e.g. cellular phone.

Heartbeat Technology

Heartbeat Technology module

Heartbeat Diagnostics

Continuously monitors and evaluates the device status and process conditions. Generates

diagnostic messages when certain events occur and provides troubleshooting measures in

accordance with NAMUR NE 107.
Heartbeat Verification

Performs a verification of the current device status upon request and generates a

Heartbeat Technology verification report showing the result of the verification.
Heartbeat Monitoring

Continuously provides device and/or process data for an external system. Analysis of this

data forms the basis for process optimization and predictive maintenance.

7.1.4

LED module VU120 (optional)

Depending on the MAX/MIN setting, an LED indicates the operational status (switch

status or alarm status) in green, yellow and red. The LED is lit very brightly and is clearly

visible from a large distance.
Connection to the following electronic inserts: FEL62, FEL64, FEL64 DC.

For more details, see the "Electrical connection" section.

Commissioning

8.1

Function check

Before commissioning the measuring point, check whether the post-mounting and post-

connection checks have been performed:
•

Checklist in "Post-mounting check" section

•

Checklist in "Post-connection check" section

8.2

Functional test using key on electronic insert

• The functional test must be performed in the OK state: MAX safety and sensor free or

MIN safety and sensor covered.

• The LEDs flash one after another as a chaser light during the functional test.

• When performing the proof test in safety instrumented systems according to SIL or

WHG: comply with the instructions in the Safety Manual.

Summary of Contents for Liquiphant FTL64

































































Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands

Endress+Hauser Liquiphant FTL64, Operating Instructions Manual

Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands