Endress+Hauser Liquiline To Go CYM290 Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 64

background image

15

pH

Oxy Cond

Calibration Record

Shows the data of the last calibration performed on the currently connected sensor.

Information

1)  In measuring mode, press the Menu softkey.
2)  Select “Information” and confirm by pressing E.
3)  Select the desired submenu and confirm by pressing E.

The different submenus are described below.

Sensor Information (Digital Sensors only)

Shows the data of the currently connected digital sensor. You can save sensor data
(MemoLog) in the device by pressing the “Save” softkey. The following table shows
the sensor information depending on the respective sensor type:

pH

Cond

Oxy

ISFET

ORP

Manufacturer

P

P

P

P

P

Order No.

P

P

P

P

P

Sensor serial no.

P

P

P

P

P

Cap serial no.
SW version

P

P

P

P

P

HW version

P

P

P

P

P

Calibration*

P

P

P

P

P

Zero point

P

P

Slope

P

P

P

Sensor operating time

P

P

P

P

P

Wear

P

P

P

SIP

P

P

P

P

P

CIP

P

Cell constant

P

Operating point

P

ORP correction

P

* Last calibration

«
...
13
14
15
16
17
...
»

Summary of Contents for Liquiline To Go CYM290

































































Reviews:

No comments

Related manuals for Liquiline To Go CYM290

Brand: Teac Pages: 148

Brand: IFM Pages: 25

Brand: Campbell Pages: 16

Brand: Bante Instruments Pages: 6

Brand: Callaway Pages: 13

Brand: Kamstrup Pages: 100

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 12

Brand: Kamstrup Pages: 60

Brand: Kamstrup Pages: 136

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 155

Brand: Unitech Pages: 18

Brand: SecureAlert, Inc. Pages: 7

Brand: GANN Pages: 89

WD-35606-00, WD-35606-05

Brand: Oakton Pages: 10

Brand: Fuji Electric Pages: 85

Brand: POSEIDON Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands