manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 98 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 98

Commissioning

Proline Promag P 500 HART

98

Hauser

10.4.3   Displaying the I/O configuration

The 

I/O configuration

 submenu guides the user systematically through all the parameters

in which the configuration of the I/O modules is displayed.

Navigation

"Setup" menu → I/O configuration

‣

I/O configuration

I/O module 1 to n terminal numbers

→   98

I/O module 1 to n information

→   98

I/O module 1 to n type

→   98

Apply I/O configuration

→   98

Alteration code

→   98

Parameter overview with brief description

Parameter

Description

User interface / Selection / 

User entry

Factory setting

I/O module 1 to n terminal numbers Shows the terminal numbers used by the I/O

module.

• Not used
• 26-27 (I/O 1)
• 24-25 (I/O 2)
• 22-23 (I/O 3)
• 20-21 (I/O 4)

 *

–

I/O module 1 to n information

Shows information of the plugged I/O
module.

• Not plugged
• Invalid
• Not configurable
• Configurable
• HART

–

I/O module 1 to n type

Shows the I/O module type.

• Off
• Current output

 *

• Current input

 *

• Status input

 *

• Pulse/frequency/switch

output

 *

Off

Apply I/O configuration

Apply parameterization of the freely
configurable I/O module.

• No
• Yes

No

Alteration code

Enter the code in order to change the I/O
configuration.

Positive integer

0

*

Visibility depends on order options or device settings

10.4.4   Configuring the status input

The 

Status input

 submenu guides the user systematically through all the parameters that

have to be set for configuring the status input.

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments