Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 62

Page: 62 / 210

Electrical connection

Proline Promag P 500 HART

Hauser

5. To ensure that moisture does not enter the cable entry:

Route the cable so that it loops down before the cable entry ("water trap").


A0029278

6. Insert dummy plugs into unused cable entries.

7.7

Post-connection check

Are cables or the device undamaged (visual inspection)?



Do the cables used meet the requirements?



Do the cables have adequate strain relief?



Are all the cable glands installed, firmly tightened and leak-tight? Cable run with "water trap"
→  61 ?



Is the potential equalization established correctly ?



Summary of Contents for Hart Proline Promag P 500



















































































































































































































Search results

Summary of Contents for Hart Proline Promag P 500

Reviews:

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 62 / 210

Search results

Summary of Contents for Hart Proline Promag P 500

Reviews: