Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 134

Page: 134 / 210

Commissioning

Proline Promag P 500 HART

134

Hauser

10.7.2 Write protection via write protection switch

Unlike parameter write protection via a user-specific access code, this allows write access

to the entire operating menu - except for the

"Contrast display" parameter

- to be locked.

The parameter values are now read only and cannot be edited any more (exception

"Contrast display" parameter

• Via local display

• Via HART protocol

Proline 500 – digital

WARNING

Excessive tightening torque applied to the fixing screws!

Risk of damaging the plastic transmitter.

‣

Tighten the fixing screws as per the tightening torque: 2 Nm (1.5 lbf ft)

Power

I/O 2

I/O 3

Off

ESC

Power

open

press

open

press

ESC

I/O 4

Power

I/O 2

I/O 3

A0029673

1. Open the housing cover.
2. Remove the display module.
3. Fold open the terminal cover.
4. Setting the write protection (WP) switch on the main electronics module to the

position enables hardware write protection.
 In the

Locking status

parameter the

Hardware locked

option is displayed

→  136. In addition, on the local display the -symbol appears in front of the

parameters in the header of the operational display and in the navigation view.

X X X X

X X X

20.50

A0029425

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Search results

Summary of Contents for Hart Proline Promag P 500

Reviews:

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 134 / 210

Search results

Summary of Contents for Hart Proline Promag P 500

Reviews: