Endress+Hauser Hart Micropilot FMR60B Operating Instructions Manual Download Page 29 | Manualshive

Page: 29 / 84

background image

Micropilot FMR60B HART

Electrical connection

Hauser

29

NOTICE

Plug M12 and plug HAN7D: incorrect mounting can invalidate the IP protection class!

‣

The degree of protection only applies if the connecting cable used is plugged in and

screwed tight.

‣

The degree of protection only applies if the connecting cable used is specified according

to IP67, NEMA Type 4X.

‣

The IP protection classes are only maintained if the dummy cap is used or the cable is

connected.

6.4

Post-connection check

 Are the device or cables undamaged (visual inspection)?
 Do the cables used comply with the requirements?
 Do the mounted cables have strain relief?
 Cable glands mounted, securely tightened and leak-tight?
 Does the supply voltage correspond to the specifications on the nameplate?
 No reverse polarity, terminal assignment correct?
 Cover screwed down correctly?
 Cover lock tightened correctly?

«
...
27
28
29
30
31
...
»

Summary of Contents for Hart Micropilot FMR60B





















































































Reviews:

No comments

Related manuals for Hart Micropilot FMR60B

Brand: Raytheon Pages: 22

Brand: Acconeer Pages: 34

Brand: Icom Pages: 15

Brand: Icom Pages: 2

Brand: Yaesu Pages: 32

Brand: AnyTone Pages: 32

Brand: Intermec Pages: 8

Brand: BRONDI Pages: 7

Brand: Harris Pages: 264

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 4

Brand: RetroSound Pages: 2

Brand: Federal Signal Corporation Pages: 12

Brand: Medion Pages: 146

Brand: Medion Pages: 232

Brand: Medion Pages: 334

Brand: Roberts Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands