background image

Deltapilot S FMB70

About this document

Hauser

3

2.2  

Symbols used

2.2.1  

Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

2.2.2  

Electrical symbols

Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding

system.

 

Protective earth (PE)

Ground terminals that must be connected to ground prior to establishing any other

connections.
The ground terminals are located on the interior and exterior of the device:

• Interior ground terminal: protective earth is connected to the mains supply.

• Exterior ground terminal: device is connected to the plant grounding system.

2.2.3  

Symbols for certain types of information and graphics

 Permitted

Procedures, processes or actions that are permitted

 Forbidden

Procedures, processes or actions that are forbidden

 Tip

Indicates additional information

Reference to documentation

A

Reference to page

Reference to graphic

Summary of Contents for FMB70





















Reviews: