Endress+Hauser Fieldgate FXA520 Operating Instructions Manual Download Page 98

Page: 98 / 108

9 Trouble-Shooting

Fieldgate FXA520

Hauser

9.4 Firmware update

Caution!

• A firmware update is possible only with the guidance of your Hauser Service Center
Depending upon the circumstances, your Hauser Service Center may recommend:

• a firmware update via Internet

• the download of the latest HART Device Indentifiers via Internet

• reset to factory default parameters

as part of any remedial action. In Cases 1 and 2, you will be supplied with the appropriate Internet

addresses.

Procedure

1 If not already selected, press

"Switch to Administration Mode"

and log in as administrator.

2 Press

Settings => Special,

then scoll down to Firmware Update

– The Firmware Update dialog appears:

3 Proceed as instructed by your Hauser Service Center, then press

"Send"

to start the

download.

Parameters

Table 9-1: Firmware Update parameters

Parameter

Description

Download Address

Fieldgate Firmware

http address at which the firmware is stored

– The address will be supplied to you by your Hauser service center

Download Fieldgate

Firmware now

Check this box to download the firmware when

Send

is pressed

Download HART

Device Indentifier

Check this box if the latest HART device identifiers are to be downloaded to Fieldgate

– The address will be supplied to you by your Hasuer service center

Download HART

Device Identifier now

Check this box to download the firmware when

Send

is pressed

Restore to Factory

Defaults

Check this box if the Fieldgate default parameters are to be restored

Reset to Reboot

Firmware

Check this box only if you want the the Fieldgate to be rebooted with the original firmware

supplied by the factory

Test connection to

Update Server

Click on the link to check the connection

Send

Press to register your changes in the Fieldgate.

Reset

Press to discard any changes made since the previous send.

Summary of Contents for Fieldgate FXA520













































































































Search results

Summary of Contents for Fieldgate FXA520

Reviews:

Related manuals for Fieldgate FXA520

Brands by name

Popular brands

Endress+Hauser Fieldgate FXA520, Operating Instructions Manual

Search results

Summary of Contents for Fieldgate FXA520

Reviews:

Related manuals for Fieldgate FXA520

Brands by name

Popular brands