Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 43

Page: 43 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Flow measurement

Hauser

6.2

Totalizers

Example:

In this example, the volume flow should be totalised and displayed in the unit m

. Negative flows

should be added to the flow rate.

Note!
• For a description of the parameters mentioned, see

– Page 107 ff, Table 18: TOTALIZER SETUP
– Page 123 ff, Table 29: PROCESS VALUES

• Totalizer 1 can be reset. Totalizer 2 cannot be reset.

Note!
• You can also specify a customer-specific unit.



See parameter description for TOTALIZER 1

UNIT (



Page 108) and TOTALIZER 2 UNIT (



Page 109).

• The TOTALIZER 1 and TOTAL. 1 OVERFLOW parameters display the totalised flow value of the

first totalizer. The TOTALIZER 2 and TOTAL. 2 OVERFLOW parameters display the totalised
flow value of the second totalizer.



See Page 123 ff, PROCESS VALUES function group.

• You can use the MENU DESCRIPTOR parameter (



Page 110) to specify which measured value

should be displayed on the on-site display.

Description

Calibrate the device as per Section 6.1.

Change the function group:
(GROUP SELECTION



) OPERATING MENU



SETTINGS



TOTALIZER SETUP

Select a flow unit via the TOTALIZER 1 UNIT
parameter, here m

for example.

Use the NEG. FLOW TOT. 1 parameter to specify the
totalising mode for negative flows, here the "Positive"
option for example.

Reset totalizer 1 to zero via the RESET TOTALIZER
parameter.

Result:
The TOTALIZER 1 and TOTAL. 1 OVERFLOW
parameters display the totalised volume flow.

Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands